Denon ADV-M71 User Manual download pdf (Page 15)

ENGLISH

(8) Removing the speaker net (D-M71DVS only)

• The net on the front of the speaker system is detachable.

• To remove it, grasp it on both sides and pull it towards you.

• To attach the net, line up the plastic pieces holes out of the net with the sticking in the cabinet and press in.

• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under circumstances such as

when the output of the power amplifier is inadvertently short-circuited and a large current flows, when the temperature surrounding the unit

becomes unusually high, or when the unit is used at high output over a long period which results in an extreme temperature rise.

When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should this occur, please

follow these steps: be sure to switch off the power of this unit, check whether there are any faults with the wiring of the speaker cables or

input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation condition around the unit and switch the power back

on.

If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off

the power and contact a DENON service center.

Protector circuit

• The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an impedance lower

than the specified impedance (for example speakers with an impedance of lower than 4 Ω/ohms) are connected. If the protector circuit is

activated, the speaker output is cut off. Turn off the set’s power, wait for the set to cool down, improve the ventilation around the set, then

turn the power back on.

Note on speaker impedance

• With this unit’s speaker outputs, signals with the reverse phase of the “+” side output terminal’s signals are also output from the “-” side

output terminal.

Do not connect to a device for switching between multiple speakers (a speaker selector or audio channel selector) or connect in ways other

than described in this manual. Doing so will result in damage.

Cautions on connecting

(8) Speaker system connections

Be sure to turn the amplifier’s power off when connecting the

speaker systems.

• Use the included cables to connect the input terminals on the back

of the speaker systems (see diagram) to the amplifier’s speaker

output terminals. Connect the speaker system for the left channel

amplifier’s “L” terminals, the one for the right channel to the

amplifier’s “R” terminals, matching the polarities (“≈” and “√”

marks). Inverting the polarities will result in unnatural sound, with

the phase off or no low bass sound. Also check that all two terminal

knobs are tightly fastened.

Connections

(The red terminals on the right side are the “≈” terminals, the black

ones on the left side the “√” terminals.)

Loosen the terminals knobs, insert the cables’

core wires, then tighten the knobs.

Connect to amplifier’s “≈” side. (Copper color)

Connect to amplifier’s

“√” side. (Silver color)

NOTE:

Make sure the core wires do not touch

each other.

Connecting the speaker cords

Use the included connection cords to connect the input terminals on

the backs of the speaker systems (see the diagram at the right) to the

ADV-M71’s speaker output terminals.

• Connect the speaker system for the left channel to the “L”

terminals, the speaker system for the right channel to the “R”

terminals, and be sure the polarities (“+” and “–”) are properly

interconnected.

• Note that if the polarities are inverted, the phase may be off and the

bass sound may be missing, resulting in an unnatural sound. Also

check that both the speaker terminal’s screws are tightly screwed.

Either twist the core wires

firmly or terminate the wires.

qTurn the speaker

terminal

counterclockwis

e to loosen it.

wInsert the cord’s

core wires.

eTurn clockwise to

tighten the

terminal.

When using banana plugs, turn

clockwise to tighten the terminal

before inserting.

Connecting banana plugs

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 111 112

Comments to this Manuals

No comments

Denon ADV-M71 User Manual Page 15

Comments to this Manuals

Related products and manuals for Acoustics Denon ADV-M71