Denon ADV-M71 User Manual Page 43

  • Download
  • Add to my manuals
  • Print
  • Page
    / 112
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 42
43
ENGLISH
1
In the still mode, press one of the 6 / 7 buttons on the
remote control unit.
6 : Reverse direction
7 : Forward direction
When pressed again, the slow play speed increases.
(Four step) (Three step on video CDs)
Press the PLAY button to resume normal playback.
(9) Slow Playback (for DVDs and video CDs only)
76
Remote control unit
NOTE:
Reverse slow play is not possible on video CDs.
B
BAND
PHONES
VOLUME
ON / STANDBY
DVD SURROUND RECEIVER ADV-M71
TONE /SDB
FUNCTION
MENU/ SET
+
-
SURROUND /SELECT
PUSH
-
PARAM.
VIRTUAL SPEAKER
5
1
3
+
-
-
A / V
3
STAT U S
SETUP TONE /SDB
FUNCTIONSURROUNDINPUT MODETEST TONE
DVD
TUNER
CH
654
987
0
/
10
CALL
ENTER
MUTING
+
10
SYSTEM MD
CDR TAPE
TUNER TV / VCR
SURROUND
AUTO DECODE
VIRTUALDIRECT
5CH STEREO
STEREO
IN
/
SURR.
IN
/
SURR.
DVD
9
8
21
76
+
-
5
2
3
1
12
OPERATING THE SURROUND FUNCTIONS
Input mode setting
1
Press the FUNCTION button to select the input function to be
played.
FUNCTION
FUNCTION
The function switches as shown below.
Factory default (LINE 1) = MD, (LINE 2) = TAPE
DVD
TUNER (LINE2)
D.AUX
(LINE1)
Main unit Remote control unit
2
When DVD, D.AUX or (LINE1) = MD was selected as the
input function, press the remote control units INPUT MODE
button to select the input mode.
INPUT MODE
•“ANALOG cannot be selected when DVD or D.AUX was
selected as the input function.
•“ANALOG can be selected when LINE-2 is set to
D.AUX at FUNCTION ASSIGNMENT under SYSTEM
SETUP in the detailed settings.
AUTO PCM DTS ANALOG
Remote control unit
Input mode selection function
The input mode can be selected when the input function is
set to DVD, D.AUX or (LINE1) = MD.
Different input modes can be selected for each input
function. The selected input mode is stored in the memory
for the individual input functions.
When the input function is set to something other than the
above, ANALOG ONLY is displayed and the input mode
cannot be selected.
q AUTO (auto mode)
In this mode, the type of signal being input to the digital
and analog input terminals is detected and the program in
the sets surround decoder is switched automatically to
play the signals for the selected input function.
The presence or absence of digital signals is detected, the
signals input to the digital input are identified and decoding
and playback are performed automatically in DTS, Dolby
Digital or PCM (2 channel stereo) format.
If no digital signal (LINE1) = MD is being input, the analog
input jacks are selected.
Use this mode to play Dolby Digital signals.
w PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM
signals are being input.
e DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when DTS
signals are being input.
r ANALOG (exclusive analog audio signal playback mode)
The signals input to the analog input jacks are played.
(
This cannot be selected in the DVD mode.)
The input mode automatically switches to AUTO if you
switch the input function to DVD from anything other than
DVD.
Page view 42
1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 111 112

Comments to this Manuals

No comments