Denon PMA-2020AE Owner's Manual download pdf (Page 18)

Remote control unit

Inserting the batteries

q Remove the rear lid in the

direction of the arrow and

remove it.

w Load the two batteries properly

as indicated by the marks in the

battery compartment.

R03/AAA

e Put the rear cover back on.

NOTE

•Insert the speciﬁed batteries in the remote control unit.

•Replace the batteries with new ones if the set does not operate

even when the remote control unit is operated close to the unit. (The

supplied batteries are only for verifying operation. Replace them

with new batteries at an early date.)

•When inserting the batteries, be sure to do so in the proper direction,

following the q and w marks in the battery compartment.

•To prevent damage or leakage of battery ﬂuid:

•Do not use a new battery together with an old one.

•Do not use two different types of batteries.

•Do not attempt to charge dry batteries.

•Do not short-circuit, disassemble, heat or dispose of batteries in

ﬂames.

•Do not keep the battery in a place exposed to direct sunlight or in

places with extremely high temperatures, such as near a heater.

•If the battery ﬂuid should leak, carefully wipe the ﬂuid off the inside

of the battery compartment and insert new batteries.

•Remove the batteries from the remote control unit if it will not be in

use for long periods.

•Used batteries should be disposed of in accordance with the local

regulations regarding battery disposal.

•The remote control unit may function improperly if rechargeable

batteries are used.

Operating range of the remote control unit

Point the remote control unit at the remote sensor when operating it.

30°30°

Approx. 8 m

NOTE

•The set may function improperly or the remote control unit may not

operate if the remote control sensor is exposed to direct sunlight,

strong artiﬁcial light from an inverter type ﬂuorescent lamp or

infrared light.

•When using 3D video devices that transmit radio communication

signals (such as infrared signals etc) between the various units (such

as the monitor, 3D glasses, 3D transmitter unit etc), the remote

control unit may not operate due to interference from those radio

communication signals. If this occurs, adjust the direction and

distance of the 3D communication for each unit, and check that the

remote control unit operation is not affected by these signals.

Explanation terms

Bi-wiring connection

This method of connecting a speaker by using two speaker cables

enables separate transmission of treble and bass signals.

This enables playback with minimal interference between the high-

range speaker unit and the low-range speaker unit.

MM/MC cartridge select

There are two types--MM (Moving Magnet) and MC (Moving Coil)--of

cartridges for turntable.

As the output levels for these two types of cartridges differ, the setting

of the phono equalizer that is mounted in this unit must be switched

according to the type of cartridge for your turntable. For switching, use

the MM/MC cartridge select button.

Protection circuit

This is a function to prevent damage to components within the power

supply when an abnormality such as an overload or excess voltage

occurs for any reason.

In this unit, the power indicator blinks and the unit enters standby

mode when an abnormality occurs.

Source direct

Playback with higher ﬁdelity to the source becomes possible, as input

audio signals are output by bypassing the audio quality-control circuits

(bass/treble/balance).

Speaker impedance

This is certain-rated resistance of the speaker set to an alternating

current and expressed in ohms.

The smaller the impedance, the greater the output. However, load

on the ampliﬁer is increased. Use speakers whose impedance is

supported by this unit.

Preparations

Operations

InformationInformation

1 2 ... 13 14 15 16 17 18 19 20 21 22

Comments to this Manuals

No comments

Denon PMA-2020AE Owner's Manual Page 18

Comments to this Manuals

Related products and manuals for Audio amplifiers Denon PMA-2020AE