Denon 483 Operations Instructions Page 26
- Page / 55
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
26
ENGLISH
• To increase the bass or treble: Press
the SELECT UP button. (The bass or
treble sound can be increased to up
to +10 dB in steps of 2 dB.)
• To decrease the bass or treble: Press the SELECT DOWN
button. (The bass or treble sound can be decreased to up
to –10 dB in steps of 2 dB.)
To select the surround mode while adjusting
the surround parameters, channel volume or
tone control, press the surround mode
button then operate the selector.
(See page 29.)
3
Select the play mode.
Press the SURROUND MODE button, then press the SELECT
button.
(Main unit) (Remote control unit)
4
Start playback on the selected component.
• For operating instructions, refer to the component’s
manual.
5
Adjust the volume.
MASTER VOLUME
MASTER
VOL
(Main unit) (Remote control unit)The volume level is
displayed on the
master volume level
display.
The volume can be adjusted within the range of –60 to 0 to 18 dB,
in steps of 1 dB. However, when the channel level is set as
described on page 29, if the volume for any channel is set at +1 dB
or greater, the volume cannot be adjusted up to 18 dB. (In this case
the maximum volume adjustment range is “18 dB — (Maximum
value of channel level)”.)
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs are played in the
“ANALOG” or “PCM” mode.
When playing DTS-compatible sources, be sure to connect the
source component to the digital input jacks (OPTICAL/COAXIAL)
and set the input mode to “DTS”.
Input mode display
ANALOGDIGITAL
DIGITAL
DIGITAL
ANALOG
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
• In the AUTO mode
• In the DIGITAL PCM mode
• In the DIGITAL DTS mode
• In the ANALOG mode
One of these lights, depending on the
input signal.
Input signal display
SIGNAL
DIGITAL
DIGITAL
DIGITAL
SIGNAL
SIGNAL
• DOLBY DIGITAL
• DTS
• PCM
The indicator lights when digital signals are being input
properly. If the indicator does not light, check whether
the digital input component setup (page 20) and connections are
correct and whether the component’s power is turned on.
DIGITAL
DIGITAL
NOTE:
• The indicator will light when playing CD-ROMs
containing data other than audio signals, but no sound will be
heard.
DIGITAL
After starting playback
[1] Adjusting the sound quality (tone)
1
The tone switches as follows each time the TONE CONTROL
button is pressed.
BASS TREBLE
2
With the name of the volume to be
adjusted selected, press the SELECT
button to adjust the level.
B
13 2
SURROUND
MODE
(Main unit)
(Main unit)
3
If you do not want the bass and treble to be adjusted, turn on
the tone defeat mode.
The signals do not pass through the
bass and treble adjustment circuits,
providing higher quality sound.
- AVR-1403/483 1
- WARNING: 2
- ATTENTION 2
- SAFETY INSTRUCTIONS 3
- TABLE OF CONTENTS 4
- BEFORE USING 4
- 0.3 ft (10 cm) or more 5
- PART NAMES AND FUNCTIONS 6
- Remote control unit 7
- Step 3 (page 16 to 20) 8
- Step 2 (page 15) 8
- Step 1 (page 8 to 14) 8
- CONNECTIONS 9
- Connecting a TV/DBS tuner 10
- Connecting a video decks 10
- R VIDEO OUTL 11
- 3. Return the lever 12
- Speaker system connections 13
- Protector circuit 14
- Note on speaker impedance 14
- Inserting the batteries 15
- USING THE REMOTE CONTROL UNIT 15
- SETTING UP THE SYSTEM 16
- *SYSTEM SET UP 17
- 1 FRONT LARGE 17
- 2 CENTER SMALL 17
- 3 SURR. SMALL 17
- 4 S.WOOFER YES 18
- Setting the SUBWOOFER MODE 18
- 5 SW MODE NORM 18
- 6 FRNT/SW 12ft 19
- 7 CENTER 12ft 19
- 8 SURR. 10ft 19
- Digital input setup 20
- 9 COAX DVD 20
- 10 OPT TV 20
- After setting up the system 20
- REMOTE CONTROL UNIT 21
- OPERATION 24
- Playing the input source 25
- After starting playback 26
- (Main unit) 27
- (Remote control unit) 27
- Simultaneous recording 28
- SURROUND 29
- Dolby Surround Pro Logic 30
- II Mode: 31
- CINEMA EQ OFF 32
- D.COMP. OFF 33
- LFE 0dB 33
- DEFAULT Y/N 33
- DSP SURROUND SIMULATION 34
- ROOM SIZE MED 35
- EFFECT LEVEL 10 35
- DELAY 30ms 36
- DEFAULT Y/N 36
- LISTENING TO THE RADIO 39
- Auto tuning 40
- Manual tuning 40
- Preset stations 41
- Recalling preset stations 41
- LAST FUNCTION MEMORY 42
- ADDITIONAL INFORMATION 43
- DTS Digital Surround 45
- TROUBLESHOOTING 46
- SPECIFICATIONS 47
- ENGLISH FRANCAIS 48
- ENGLISHFRANCAIS 49
- Telephone: (03) 3837-5321 50
Related products and manuals for AV receivers Denon 483
AV receivers Denon AVR-S500BT Owner's Manual
(140 pages)
(140 pages)
(74 pages)
AV receivers Denon AVR-X1100W Owner's Manual
(259 pages)
(259 pages)
(48 pages)
© 2020, manymanuals.com. All rights reserved. | 0.504 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals