AV SURROUND RECEIVERAVR-5800OPERATING INSTRUCTIONSMASTER VOLUMEREMOTE SENSORON / STANDBYINPUT SELECTORHOMETHX CINEMAPURE DIRECTVOLUME LEVELAL24RFLOCKD
101423Connecting the antenna terminalsDIRECTION OF BROADCASTING STATIONAM LOOP ANTENNA(Supplied)FM ANTENNAGROUNDAM OUTDOORANTENNA300 Ω/ohmsTERMINALSFM
11Connecting the external input (EXT. IN) jacksConnecting the MULTI SOURCE jacks• These jacks are for inputting multi-channel audio signals from an ou
12Speaker system connections• Connect the speaker terminals with the speakers making sure that likepolarities are matched ( < with < , > with
13Connections• When making connections, also refer to the operating instructions of the other components.SPEAKER SYSTEMSANTENNA TERMINALSMULTIZONESURR
146PART NAMES AND FUNCTIONSFront Panel• For details on the functions of these parts, refer to the pages given in parentheses ( ).qPower indicator...
15Remote control unit• For details, refer to the separate (supplied) RC-8000 operating instructions.The USB terminal is a terminal that will be used i
167SETTING UP THE SYSTEM• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 6 to 13), make th
17• Speaker system layoutBasic system layout (For a THX Surround EX system)• The following is an example of the basic layout for a system consisting o
18Before setting up the system1Check that all the connections arecorrect, then turn on the main unit’spower.2Either lightly press on the remote contro
19Setting the type of speakers• The composition of the signals output from the different channels and the frequency response are adjusted automaticall
22 SAFETY PRECAUTIONS2 NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION• Avoid high temperatures.Allow for sufficient heat dispersion wheninstalle
20• ParametersLarge ...Select this when using speakers that can fully reproduce low sounds of below 80 Hz. Small ...Select t
21NOTES:— Assignment of low frequency signal range —• The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby D
22Setting the delay time• Input the distance between the listening position and the different speakers to set the delay time for the surround mode.• T
236Set the distance between thecenter speaker and listeningposition.The distance changes in units of 1foot (0.1 meters) each time thebutton is pressed
244Select the desired setting, then press jog stick “ENTER”.Variable:The level can be adjusted freely using the buttons on the remote control unit (M.
25Setting the channel level• Use this setting to adjust so that the playback level between the different channels is equal.• From the listening positi
267Select “Yes”.8a. If the “Auto” mode is selected: Test tones are automatically emitted from the different speakers.The test tones are emitted from t
27Subwoofer peak limit level setting• This unit features a subwoofer peak limit control which prevents distortion and damage in the loudspeaker system
28CAUTION!• The master volume is set to “–30 dB” when test tones are output.• The test tones are for confirming the low frequency playback limits and
29Setting the on-screen display (OSD)• Use this to turn the on-screen display (messages other than the menu screens) on or off.1At the System Setup Me
3SAFETY INSTRUCTIONS1. Read Instructions – All the safety and operatinginstructions should be read before the appliance isoperated.2. Retain Instructi
302Switch to the Auto Preset Memory screen.3Select “Yes” for Start.“Search” flashes on the screen and searching begins.“Completed” appears once search
318REMOTE CONTROL UNIT• The included remote control unit (RC-8000) can be used to operate not only the AVR-5800 but other remote control compatible DE
32Operating the remote control unit12Remote control unit’s jog stickLightly press “ENTER” to display the icons.Press the “ ” button on the icon displa
33Playing the input source213 51Select the input source to be played.INPUT SELECTOR(Main unit) (Remote control unit)Example: CDWhen the input source i
343Select the play mode.STEREO(Main unit) (Remote control unit)Example: Stereo4Start playback on the selected component.• For operating instructions,
353Adjust as desired with the CONTROL knob.• To increase the bass or treble: Turn the control clockwise. (The bass or treble sound can be increased to
36Multi-source recording/playback[1] Playing one source while recording another (REC OUT mode)1Press the REC/M-ZONE 2 button until“REC OUT SOURCE” app
37[3] Outputting a program source to an amplifier, etc., in a different room (M-ZONE 1 mode)1Press the M-ZONE 1 button.M-ZONE 12Select the source you
38Playback using the external input (EXT. IN) jacks1Set the external input (EXT. IN) mode.Press the EXT. IN (on the EXT. IN button on the remote contr
39Playing audio sources (CDs and DVDs)The AVR-5800 is equipped with three 2-channel playback modes exclusively for music.Select the mode to suit your
42 INTRODUCTION2 ACCESSORIESThank you for choosing the DENON AVR-5800 Digital Surround A / V receiver. This remarkable component has been engineered t
40Multi-source and multi-zone playbackMULTI ROOM MUSIC ENTERTAINMENT SYSTEM• When the outputs of the MULTI SOURCE AUDIO OUT terminals are wired and co
41[2] Multi-zone playback using the MULTI ZONE 2 terminalsThe AVR-5800 is equipped with audio pre output terminals with a fixed output level (M-ZONE 2
4210SURROUNDBefore playing with the surround function• Before playing with the surround function, be sure to use the test tones to adjust the playback
43Fader function• This function makes it possible to lower the volume of the front channels (FL, C and FR) or the rear channels (SL, SR, SBL and SBR)
44Playing modes for different sourcesThe AVR-5800 is equipped with many surround modes. We recommend using the surround modes as described below in o
45[1] Playing sources recorded in Dolby Pro Logic in the Home THX Cinema surround mode1Select the Home THX Cinema mode.HOMETHX CINEMA(Main unit) (Remo
46Dolby Digital mode (only with digital input) and DTS Surround (only with digital input)1Select the input source.INPUT SELECTOR(Main unit) (Remote co
47Surround parameters wCINEMA EQ. (Cinema Equalizer):The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating f
4811DENON ORIGINAL SURROUND MODES• The AVR-5800 is equipped with a built-in high performance DSP (digital signal processor) that uses digital processi
49DSP surround simulation1Select the surround mode for the input channel.DIRECT STEREODOLBYSURROUNDDTSSURROUNDWIDESCREEN5CH / 7CHSTEREODSPSIMULATIONSU
53CAUTIONS ON HANDLING4FEATURES• Switching the input function when input jacks are notconnectedA clicking noise may be produced if the input function
50Tone control setting• Use the tone control setting to adjust the bass and treble as desired.1Display the surround parameterscreen on the monitor.The
51Surround parameters eEFFECT:This parameter turns the effect signals with multi surround mode speaker effects on and off in the WIDE SCREEN mode. Wh
5212LISTENING TO THE RADIOAuto tuning1Set the input function to “TUNER”.INPUT SELECTOR(Main unit) (Remote control unit)2Watching the display, press th
53Preset memory1Use the “Auto tuning” or “Manual tuning” operation to tunein the station to be preset in the memory.2Press the MEMORY button.3Main uni
54Recalling preset stations1Main unit:Watching the display, press the MODE SELECT button until“TUNER PRESET” appears on the set’s display.Remote contr
5515TROUBLESHOOTING If a problem should arise,first check the following.1. Are the connections correct ?2. Have you operated the receiver according to
5616ADDITIONAL INFORMATIONOptimum surround sound for different sourcesThere are currently various types of multi-channel signals (signals or formats w
57Surround back speakersThe THX Surround EX format adds new “Surround Back” (SB) channels to the conventional 5.1-channel system. This makes it easy
58• Set the front speakers, center speaker and subwoofer in the samepositions as in example (1).• It is best to place the surround speakers directly a
59• Set the front speakers slightly wider apart than the setup for watching movies only and point them toward the listeningposition in order assure cl
65CONNECTIONS• Do not plug in the AC cord until all connections have been completed.• Be sure to connect the left and right channels properly (left wi
60SurroundThe AVR-5800 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the sam
61(2) Dolby Pro LogicDolby Pro Logic is a multi-channel signal playback system developed by Dolby Laboratories which decodes sources recorded in Dolby
62DTS-ES Extended Surround TMDTS-ES Extended Surround is a new multi-channel digital signal format developed by Digital Theater Systems Inc. While of
63Home THX Cinema surround modeTHX is an exclusive set of standards and technologies established by the world-renowned film production company, Lucasf
64System setup items and default values (set upon shipment from the factory)System setup Default settingsqwtyuioSpeakerConfiguration(SurroundSpeakerSe
65Surround modes and parametersSignals and adjustability in the different modesChannel output Parameter (default values are shown in parentheses)When
6617SPECIFICATIONS 2 Audio section• Power amplifierRated output: Stereo (2ch driven) (All properties shown are only 170 W + 170 W (8 Ω/ohms, 20 Hz ~
14-14, AKASAKA 4-CHOME, MINATO-KU, TOKYO 107-8011, JAPANTelephone: (03) 3584-8111Printed in Japan 511 3624 006
7Connecting video components• To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a
8Connecting a video component equipped with S-Video jacks• When making connections, also refer to the operating instructions of the other components.•
9Connecting a Video Component Equipped with Color Difference (Component - Y, R-Y, B-Y) VideoJacks (DVD Player)• When making connections, also refer to
Comments to this Manuals