Denon DBP 4010UDCI User Manual download pdf (Page 27)

TroubleshootingInformationHDMI Control FunctionPlaybackConnectionsGetting Started Speci cations

ENGLISH

2

HDMI Setup

Setting items

Setting contents

Audio Setup

GMulti LPCM BM OffH : Decoded Linear PCM multi-channel signal is

output by the DBP-4010UDCI. This setting is not made in speaker setting.

(BM: Bass Management)

G2chH : Output the downmixsed 2-channel LPCM signal.

GMuteH : Do not output audio from HDMI.

SA-CD Audio Out

Set to output stereo/multi

area audio of Super Audio

CD to the HDMI terminal.

On : Super Audio CD audio is output.

Off : Super Audio CD audio is not output.

The Super Audio CD audio signal is a 44.1 kHz/16-bit Linear PCM output.

HDMI Control

Can operate the unit in

conjunction with an HDMI

control support device.

GControlH

Off : Disable the HDMI control function.

On : Link with the device connected to HDMI.

GPower Off ControlH

On : Turns the DBP-4010UDCI’s power to standby through linkage to

the TV.

Off : Does not turn the DBP-4010UDCI's power to standby through

linkage to the TV.

For the HDMI control function to operate, it is necessary for the DBP-

4010UDCI or HDMI-compatible TV connected to the DBP-4010UDCI to

have an HDMI connection.

Refer to “HDMI Control Function” (vpage 47) for more information

about the HDMI control function.

The HDMI control function from the connected device becomes valid

when, on the GUI menu, “DENON LINK Setup” – “DENON LINK Mode”

is set to “4th” (vpage 28).

After the “HDMI Control” setting has been changed, always turn off the

power to the connected equipment and then turn it back on.

•

NOTE

If you set “DENON LINK Setup” – “DENON LINK Mode” on the GUI menu to “4th”, you will no longer

be able to change the “HDMI Control” – ”Control” setting. To change the setting, switch “DENON LINK

Mode” to a setting other than “4th”  rst and then change the setting.

Setting items

Setting contents

TV Aspect (Aspect ratio)

Set the screen type and

display mode of the TV.

16:9 Squeeze Auto : Output to a wide screen TV. For 4:3 video, display in

the center of the screen without changing the aspect ratio.z1

WIDE (16:9) : Output to a wide screen TV.

4:3 PS : Output to a 4:3 TV. For wide video, trim the left and right side of

the image and display in 4:3 aspect ratio. z2

4:3 LB : Output to a 4:3 TV. Display all of the wide video.

Component Resolution z3

Set the component output

resolution.

480/576i, 480/576P, 720P, 1080i,

Source Direct : Output video using its source resolution. Convert the

1080p video source to 1080i.

Progressive Mode

Set an appropriate

progressive conversion

mode for the source video

material.

Auto : Detect the type of video material and automatically switch the

mode. Normally, this setting is used.

Video1 : Suitable for playing video material discs.

Video2 : Suitable for playing video material discs or 30-frame  lm material

discs.

TV Active Area

Sets the horizontal display

range when the analog

video output resolution is

480i/576i.

Full : Set when a home-use monitor is connected.

Normal : This setting is used when video synchronization is disturbed on

a professional-use monitor.

This is not available for HDMI output.

z1 :

This has no effect with the video and S-Video outputs.

z2 :

Depending on the video content, even though you set the 4:3 PS (Pan Scan), the content may be

output in 4:3 LB (Letter Box).

z3 :

When video is output from the HDMI terminal, no video signals are output from the component

terminals.

Set the video output signal according to the connected TV.

Video Setup

Default settings are underlined.

Remote control operation

buttons

Displaying the menu

Cancel the menu

Moves the cursor

(Up/Down/Left/Right)

:Decision the setting :Return to previous menu

Setup

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 68 69

Comments to this Manuals

No comments

Denon DBP 4010UDCI User Manual Page 27

Comments to this Manuals

Related products and manuals for Blu-Ray players Denon DBP 4010UDCI