Denon DBP 4010UDCI User Manual Page 29

  • Download
  • Add to my manuals
  • Print
  • Page
    / 69
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 28
TroubleshootingInformationHDMI Control FunctionPlaybackConnectionsGetting Started Specications
ENGLISH
2
Setting items
Setting contents
7.1ch Audio Out
NOTE
Select “Large” or “Small” not according to the physical size of the
speaker but according to the low frequency reproduction capabilities
based on the frequency set at “Crossover Freq.”.
On the GUI menu, if the Audio Setup” “7.1ch Audio Out”– “Multi
Channel “Speaker Conguration item setting is changed, other
settings are automatically changed as well.
GExampleH
If you set “Front” to “Small”, “Subwoofer” is set to “Yes” and “Large”
cannot be selected for “Center”, “Surround” and “Surr. Back”.
Audio signal (sampling frequency, number of channels) from the
HDMI output terminal may be restricted by the specication of the
HDMI audio that can be input by the device at the other side.
GExampleH
If the HDMI audio specication of the device at the other side is the
5.1 channel, even when DBP-4010UDCI plays back by the 7.1 channel,
the 5.1 channel audio is automatically output. In that case, the analog
audio output becomes the 5.1 channel output as well.
n Channel Level : Set the volume of the test tone to be the same when
it is output from each speaker.
GModeH : Select a test tone output method.
Auto : Automatically switch the test tone output speaker.
Manual : Manually switch the test tone output speaker.
GStartH : Begin outputting the test tone.
Front L / Center / Front R / Surround R /
Surr. Back R / Surr. Back L / Surround L / Subwoofer
When the test tone output stops, press .
GSW +10dBH : Increase the subwoofer output level by 10 dB.
z
Off : Do not change the subwoofer output level.
On : Increase the subwoofer output level by +10 dB.
z : “SW +10dB” cannot be set for “HDMI Setup Audio Setup
“Multi LPCM BM On” – “Channel Level” on the GUI menu.
GDefaultH : Reset all channel level settings to factory default.
No : Do not Reset.
Yes : Reset.
b
Audio Setup
Setting items
Setting contents
7.1ch Audio Out
n Distance : Set the distance between the listening position and each
speaker.
GFeetH or GMetersH : Set the unit of distance.
GStepH : Set the minimum variable width of the distance.
1ft, 0.1ft, 0.1m, 0.01m
GDefaultH : Reset all distance settings to factory default.
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
Surr. Back L / Surr. Back R : Select the speaker you want to set,
and set the distance. Set the value that is closest to the measured
distance.
0 ~ 60ft or 0 ~ 18m
Default settings :
Front/Center/Subwoofer : 12 feet (3.6 meters)
Surround/Surr. Back : 10 feet (3.0 meters)
Set the difference in the distance betweem the speakers to less than
20 feet (6.0 meters).
NOTE
When “BD Audio Mode” is set to “HD Audio Output” (vpage 32), the
“Distance” setting is disabled during DTS-HD 192kHz audio playback.
Subwoofer Mode
Set the type of low frequency
signal to be output from the
subwoofer.
LFE : Add the low frequency signal of the channel for which the speaker
size is set to “small” to the subwoofer signal and output it.
LFE+Main : Add the low frequency signal of all channels to the subwoofer
signal and output it.
Remote control operation
buttons
:
Displaying the menu
Cancel the menu
:
Moves the cursor
(Up/Down/Left/Right)
:Decision the setting :Return to previous menu
Setup
Page view 28
1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 68 69

Comments to this Manuals

No comments