Denon DVD 3800BDCI - Blu-ray Disc DVD/CD Player Operations Instructions download pdf (Page 9)

Introduction Introduction

ENGLISH

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the remote

control and infrared sensor window on the unit.

• Remote operation may become unreliable if strong sunlight or

fluorescent light is shining on infrared sensor window of the

unit.

• Remote control for different devices can interfere with each

other. Avoid using remote control for other equipment located

close to the unit.

• Replace the batteries when you notice a fall off in the operating

range of the remote control.

• The maximum operable ranges from the unit are as follows.

If you have other DENON’s DVD players around this unit, this unit

reacts to the commands you made for DVD players through its

remote control. To avoid this situation, you can set this unit not

react to other DENON’s DVD player's remote control.

1) In stop mode, press [SETUP].

2) Press [7],[8],[9],[2].

3) Press [SETUP].

• “Only Attached Remocon” will be displayed on the upper

right corner of the screen and this unit only react to the

commands from this unit's remote control.

• To set back to default, press [7],[8],[9],[1] at step 2. “Normal

Remocon” will be displayed on the upper right corner of the

screen and this unit react to both the commands from this unit's

remote control and the other DENON’s DVD players' remote

control.

To avoid the other DENON’s BD players responding the remote

signal of this unit, you can change the signal code of the remote

control. If the signal code of the remote control does not match to

the signal code of the unit, you cannot control the unit with the

remote control.

䡵 Change the signal code of the unit

1) In stop mode, press [SETUP].

2) Use [Y / Z] to select , then press [ENTER].

3) Use [Y / Z] to select , then press [ENTER].

4) Use [U / V] to select “Remote Control Setting”.

5) Press [ENTER] to select “DENON1” or “DENON2”.

6) Press [SETUP] to exit.

• At this point the new signal code of the unit is effective. Please

change the signal code of the remote control to match to the

signal code of the unit with following procedure.

䡵 Change the signal code of the remote control

Set to “DENON1”:

Press and hold [RETURN], and press [3], [2], [1].

Set to “DENON2”:

Press and hold [RETURN], and press [1], [2], [3].

• If the signal code does not match, the signal code of the remote

control will be displayed on the front panel display.

• The default setting and the setting after you change the

batteries is “DENON1”.

About the Remote Control

Loading the Batteries

A Open the battery

compartment cover.

B Insert two “AA” (R6P)

batteries, with each one

oriented correctly.

C Close the cover.

Cautions on Batteries

• Use “AA” (R6P) batteries in this remote control.

• Replace the batteries with new ones approximately once a

year, though this depends on the frequency with which the

remote control is used.

• If the remote control does not operate within a close

proximity of the main unit, replace the batteries with new

ones, even if less than a year has passed.

• The included batteries serve only for verifying operation.

Replace them with new batteries as soon as possible.

• When inserting the batteries, be careful to do so in the

proper direction, following the and marks in the remote

control’s battery compartment.

• To prevent damage or battery fluid leakage:

- Do not mix a new battery with an old one.

- Do not mix two different types of batteries such as alkaline

and manganese.

- Do not short-circuit, disassemble, heat or dispose of

batteries in flames.

• Remove the batteries when not planning to use the remote

control for a long period of time.

• If the batteries should leak, carefully wipe off the fluid from

the inside of the battery compartment, then insert new

batteries.

Using a Remote Control

- Line of sight: approx. 23 feet (7m)

- Either side of the center: approx. 23 feet (7m) within 30°

Setting this Unit not React to Other DENON’s DVD Player's Remote Control

Note

• The setting remains after you turn off this unit or unplug the

AC cord.

• If you try to operate this unit with the other DENON’s DVD

players' remote control, some of the operation may not

available depends on the manufactured year or type of the

remote control.

SD CARD

Advanced AL24

VIDEO NR

OFF

ON / STANDBY

HDMI

RESOLUTION

VIDEO NOISE

REDUCTION

BLU-RAY DISC PLAYER

DVD-3800BDCI

30°30°

23 feet (7m) 30° 23 feet (7m) 23 feet (7m) 30°

Changing the Signal Code of a Remote Control

Power Saving

Off

Remote Control Setting

DENON1

Media Select Disc

Others

E5E00UD_EN.book Page 6 Friday, January 18, 2008 6:59 PM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 43 44

Comments to this Manuals

No comments

Denon DVD 3800BDCI - Blu-ray Disc DVD/CD Player Operations Instructions Page 9

Comments to this Manuals

Related products and manuals for Blu-Ray players Denon DVD 3800BDCI - Blu-ray Disc DVD/CD Player