Denon DRA-F100 User Manual download pdf (Page 6)

ENGLISH

ON / STANDBY

PERSONAL COMPONENT SYSTEM / STEREO CASSETTE TAPE DECK DRR-F100

REC/

REC MUTE

CD SRS

COUNTER

RESET

DOLBY NR

REC LEVEL

OPEN / CLOSE

REV. MODE

-10

+3+10-1-3-5-10

-20

-30-40

TAPE

PLAY

MIN

MAX

PHONES

BASS

TREBLE

BALANCE

SYSTEM

REMOTE SENSOR

VOLUME

ON / STANDBY

PERSONAL COMPONENT SYSTEM / AM-FM STEREO RECEIVER DRA-F100

EON-PTY

EON-TA

MHz

TUNED STEREO AUTO

TIMER

MONO /

STEREO

BAND

MEMORY

FUNCTION

DOWN

TUNING

TIMER

DISPLAY

ON / STANDBY

OPEN/CLOSE

PERSONAL COMPONENT SYSTEM / COMPACT DISC PLAYER DCD-F100

/ /

POWER LOADING MECHANISM

ON / STANDBY

EJECT

PERSONAL COMPONENT SYSTEM / MINIDISC RECORDER DMD-F100

INPUT SELECT

DIGITAL

ANALOG

REMOTE SENSOR

RANDOM

-60 -40 -30 -20 -12 -6 -2 0

OVER

D.IN

04Tr 12m 48s

EDIT

PUSH ENTER

REC LEVEL

CHARACTER

REC /

PICK REC

CD SRS

PICK REC MODE

CONNECTOR

SYSTEM

OPTICAL

DIGITAL OUT

LINE OUT

PHONO AUX CD PB-TAPE-REC PB-MD-REC

CONNECTOR

SYSTEM

R L

SPEAKERS

IMPEDANCE 4~16º

FM COAX 75º LOOP

ANT.

AC OUTLET

SWITCHED

120W(1A.)MAX

120V 60Hz

AC OUTLET

UNSWITCHED

120W(1A.)MAX

120V 60Hz

SIGNAL GND

OUTPUT INPUT

OPTICAL

CONNECTIONS

This system includes digital circuitry which may

cause interference such as color blotching or

changes in the color on TVs. If this happens,

move the system and the TV as far apart as

possible.

NOTE:

System operations

Such system operations as the timer and the auto on functions,

as well as remote control operations cannot be performed

unless all the RCA pin-plug cords and system connector cords

are connected between the units, so be sure to make all the

connections properly as shown in the diagram. Also,

disconnecting system connectors while the system is operating

may result in malfunction. Be sure to unplug the power cord

before changing connections.

AM loop

antenna

Record player

Speaker systems

Use a record player with

an MM cartridge.

• Disconnect the ground cord if

humming or noise is produced

when it is connected.

Ground cord

LD player, video deck, etc.

Power plug

AC 120 V 60 Hz

(Plug into a power outlet)

• Do not plug the power cord into the power outlet until all connections are completed. Be

sure to interconnect the channels (L to L (white) and R to R (red)) properly, as shown on the

diagram.

• Insert the plugs securely. Incomplete connections may result in noise.

• Be sure to connect the speaker cords between the speaker terminals and the speaker

systems with the same polarities (+ to +, – to –). If the polarities are switched, the sound at

the center will be weak, the position of the different instruments will be unclear, and the

stereo effect will be lost.

• After unplugging the power cord, wait about 5 seconds before plugging it back in.

• Note that setting the connection cords (pin-plug cords) next to the power cords may result

in humming or other noise.

NOTES:

AM-FM Stereo Receiver

(DRA-F100)

CD player

(DCD-F100)

Connecting the speaker systems

Connect the speaker system for the

left channel (the left side as seen

from the front) to the ”L“ terminals,

the speaker system for the right

channel to the ”R“ terminals. Be sure

to use speaker systems with an

impedance of 4 Ω/ohms or greater.

Whenever the power switch is

in the STANDBY position, the

unit is still connected on AC line

voltage.

Please be sure to unplug the

cord when you leave home for,

say, a vacation.

CAUTION:

Right Left

AC Outlets

• SWITCHED outlet (DRA-F100)

The power of this outlet is switched on and off by the receiver’s SYSTEM

power operation switch.

This outlet will also be switched on when the power is set to ON-

STANDBY with the remote control.

When the receiver is in the standby mode, the outlet switches off after

approximately 20 seconds.

• UNSWITCHED outlets (DCD-F100)

These outlets remains on at all times, regardless of the setting of the CD

player’s and cassette’s power operation switch.

✽ Do not connect the receiver’s AC cord to the outlets on the CD player

(DCD-F100). Doing so could result in damage.

PRECAUTIONS FOR

INSTALLATION

For heat dispersal, leave at least

10 cm of space between the

top, back and sides of this unit

and the wall or other

components.

Stacking installation

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article

820-40 of the NEC which provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as practical.

Connecting a MD recorder

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape recording

(OUT) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape playback

(IN) jacks using pin plug cords.

MD recorder

Connecting a tape deck

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape recording

(REC) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape playback

(PB) jacks using pin plug cords.

Tape deck

1 2 3 4 5 6 7 8 9 10 11 ... 53 54

Comments to this Manuals

No comments

Denon DRA-F100 User Manual Page 6

Comments to this Manuals

Related products and manuals for HiFi systems Denon DRA-F100