Denon AVR-1802/882 User Manual Page 27
- Page / 96
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
• To increase the bass or treble: Turn
the control clockwise. (The bass or
treble sound can be increased to up
to +12 dB in steps of 2 dB.)
• To decrease the bass or treble: Turn the control
counterclockwise. (The bass or treble sound can be
decreased to up to –12 dB in steps of 2 dB.)
To select the surround mode while adjusting
the surround parameters, channel volume or
tone control, press the surround mode
button then operate the selector.
27
ENGLISH
3
Select the play mode.
Press the SURROUND MODE button, then turn SELECT
knob.
(Main unit) (Remote control unit)
4
Start playback on the selected component.
• For operating instructions, refer to the component’s
manual.
5
Adjust the volume.
MASTER VOLUME
MASTER
VOL
(Main unit) (Remote control unit)The volume level is
displayed on the
master volume level
display.
The volume can be adjusted within the range of –60 to 0 to 18 dB,
in steps of 1 dB. However, when the channel level is set as
described on page 30, if the volume for any channel is set at +1 dB
or greater, the volume cannot be adjusted up to 18 dB. (In this case
the maximum volume adjustment range is “18 dB — (Maximum
value of channel level)”.)
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs are played in the
“ANALOG” or “PCM” mode.
When playing DTS-compatible sources, be sure to connect the
source component to the digital input jacks (OPTICAL/COAXIAL)
and set the input mode to “DTS”.
Input mode display
ANALOGDIGITAL
DIGITAL
DIGITAL
ANALOG
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
• In the AUTO mode
• In the DIGITAL PCM mode
• In the DIGITAL DTS mode
• In the ANALOG mode
One of these lights, depending on the
input signal.
Input signal display
SIGNAL
DIGITAL
DIGITAL
DIGITAL
SIGNAL
SIGNAL
• DOLBY DIGITAL
• DTS
• PCM
After starting playback
[1] Adjusting the sound quality (tone)
1
The tone switches as follows each time TONE CONTROL is
pressed.
BASS TREBLE
2
With the name of the volume to be
adjusted selected, turn SELECT knob to
adjust the level.
SELECT
B
23 1
SELECT
SURROUND
MODE
(Main unit)
(Main unit)
3
If you do not want the bass and treble to be adjusted, turn on
the tone defeat mode.
The signals do not pass through the
bass and treble adjustment circuits,
providing higher quality sound.
(Main unit)
(Main unit)
The indicator lights when digital signals are being input
properly. If the indicator does not light, check whether
the digital input component setup (page 21) and connections are
correct and whether the component’s power is turned on.
DIGITAL
DIGITAL
NOTE:
• The indicator will light when playing CD-ROMs
containing data other than audio signals, but no sound will be
heard.
DIGITAL
- AV SURROUND RECEIVER 1
- WARNING: 2
- ATTENTION 2
- SAFETY INSTRUCTIONS 3
- TABLE OF CONTENTS 4
- BEFORE USING 4
- 0.3 ft (10 cm) or more 5
- PART NAMES AND FUNCTIONS 6
- Remote control unit 7
- Step 3 (page 17 to 21) 8
- Step 2 (page 16) 8
- Step 1 (page 8 to 15) 8
- CONNECTIONS 9
- Connecting a CD player 10
- DIGITAL jacks 10
- Connecting a TV/DBS tuner 11
- Connecting a video decks 11
- Connecting a monitor TV 12
- Connecting the video decks 12
- 3. Return the lever 13
- Speaker system connections 14
- Protector circuit 15
- Note on speaker impedance 15
- Inserting the batteries 16
- SETTING UP THE SYSTEM 17
- Before setting up the system 18
- Setting the SUBWOOFER MODE 19
- 6 FRNT/SW 12ft 20
- 7 CENTER 12ft 20
- 8 SURR. 10ft 20
- Digital input setup 21
- After setting up the system 21
- REMOTE CONTROL UNIT 22
- Before operating 25
- (Main unit) 25
- Playing the input source 26
- After starting playback 27
- (Remote control unit) 28
- Simultaneous recording 29
- SURROUND 30
- Dolby Surround Pro Logic 31
- II Mode: 32
- CINEMA EQ OFF 33
- D.COMP. OFF 34
- LFE 0dB 34
- DEFAULT Y/N 34
- DSP SURROUND SIMULATION 35
- ROOM SIZE MED 36
- EFFECT LEVEL 10 36
- Auto preset memory 40
- Auto tuning 41
- Manual tuning 41
- Preset stations 42
- Recalling preset stations 42
- LAST FUNCTION MEMORY 43
- ADDITIONAL INFORMATION 44
- DTS Digital Surround 46
- TROUBLESHOOTING 47
- SPECIFICATIONS 48
- TABLE DES MATIERES 49
- AVANT L‘UTILISATION 49
- 10 cm (0.3 pieds) ou plus 50
- NOMENCLATURE ET FONCTIONS 51
- FRANCAIS 52
- Etape 3 (page 62 à 66) 53
- Etape 2 (page 61) 53
- Etape 1 (page 53 à 60) 53
- CONNEXIONS 54
- Circuit de protection 60
- Insertion des piles 61
- INSTALLATION DU SYSTEME 62
- *SYSTEM SET UP 63
- 1 FRONT LARGE 63
- 2 CENTER SMALL 63
- 3 SURR. SMALL 63
- 4 S.WOOFER YES 64
- 5 SW MODE NORM 64
- 9 COAX DVD 66
- 10 OPT1 TV 66
- 11 OPT2 CDR 66
- UNITE DE TELECOMMANDE 67
- Avant l’utilisation 70
- (Unité principale) 70
- Après le début de la lecture 72
- (Unité principale) (Unité de 73
- AMBIANCE 75
- 2, 5, 74. 61 2 76
- 4, 5, 6, 7 76
- SIMULATION D’AMBIANCE DSP 80
- (Unité de télécommande) 82
- Mémoire préréglée automatique 85
- Syntonisation automatique 86
- Syntonisation manuelle 86
- Stations préréglée 87
- Rappel de stations préréglées 87
- MEMOIRE DE DERNIERE FONCTION 88
- INFORMATIONS SUPPLEMENTAIRES 89
- DEPISTAGE DES PANNES 92
- ENGLISH FRANCIAS 94
- ENGLISHFRANCIAS 95
- Telephone: (03) 3584-8111 96
Related products and manuals for Home Theater Systems Denon AVR-1802/882
(2 pages)
(90 pages)© 2020, manymanuals.com. All rights reserved. | 0.643 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals