Denon AVR-1509 Owner's Manual Page 21
- Page / 56
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Step 4 : Check
• To proceed to “Step 5” without checking the analysis result, use ui to select “Store<”
while “Parameter Check<” is displayed.
• Values that are different from the actual distance may be set for speakers with built-in filters
(subwoofers, etc). This is because filters add electrical delay to the signal that should be
compensated.
NOTE
Do not turn the power off while the settings are being stored.
Step 5 : Store
The auto setup measurement results are stored in the AVR-1509.
q Press o while “Store<” is displayed.
• “Storing” blinks on the display panel while the results are being stored.
• When storing is complete, “Completed” is displayed followed by “Disconnect Mic”.
w Disconnect the setup microphone from the AVR-1509.
s Error Messages
If the auto setup procedure could not be completed due to speaker installation, the measuring environment,
etc. an error message is displayed. Check the relevant items and be sure to take the necessary measures. After
addressing any issues, perform the auto setup procedure over again.
NOTE
Be sure to turn the power off before checking speaker connections.
Select “Retry” to make the measurements again.
Error messages (examples) Cause Measures
M i c o r S p : N o n e
• The included setup microphone is not
connected.
• Not all speakers could be detected.
• Connect the included setup
microphone to the SETUP MIC jack
on the main unit.
• Check the speaker connections.
A m b i e n t N o i s e
• Too much noise in the room for
accurate measurements to be made.
• Speaker or subwoofer sound is too
low for accurate measurements to be
made.
• Either turn off any device generating
noise or move it away.
• Try again when the surroundings are
quieter.
• Check the speaker installation and the
direction in which the speakers are
facing.
• Adjust the subwoofer’s volume.
C a u t i o n : S p N o n e
The messages alternate
F R
• Displayed speaker could not be
detected.
· The front L and front R speakers
were not properly detected.
· Only one channel of the surround
speakers was detected.
• Check the connections of the
displayed speaker.
C a u t i o n : P h a s e
The messages alternate
S L
• Displayed speaker connected with
the polarities reversed.
• Check the polarities of the displayed
speaker.
• For some speakers, this error
message may be displayed even if
the speaker is properly connected. If
the connection is correct, use ui to
display “Skip<” and then press o.
n To switch to another analysis result item
Press ENTER.
This returns you to analysis results items, so repeat operation q.
n To proceed to “Step 5 : Store”
During display of crossover frequency result or analysis results item, press ENTER.
• “Store<” is displayed.
n To cancel storing
Use ui to display “Cancel<” while “Store<” is displayed and press o.
• All the measured auto setup data will be erased.
When analysis is complete, “Parameter Check<” is displayed.
Press o and check the analysis results for the following four items.
q Make your selection using ui and press o.
• Presence and size of speaker
“SpConfig. Check<”
• Distance of speaker from listening position
“Distance Check<”
• Speaker channel level
“Ch Level Check<”
• Crossover Frequency
“Crossover Check<”
w Use ui to change which speaker is displayed.
Getting Started Connections Setup Playback Remote Control Information Troubleshooting
ENGLISH
Specifications
- AVR-1509 1
- SAFETY PRECAUTIONS 2
- Getting Started 6
- About the Remote Control Unit 7
- Cautions on Handling 7
- Cautions on Installation 7
- Part Names and Functions 8
- Rear Panel 9
- Remote Control Unit 10
- Connections 11
- Speaker Connections 12
- Specifications 13
- Connecting the Monitor 14
- CD Player 15
- TV/CABLE Tuner 15
- Connections to Other Devices 16
- Connectors 17
- Antenna Terminals 17
- 1 H D M I 1 : D V D 18
- Auto Setup 19
- Step 4 : Check 21
- Step 5 : Store 21
- System Setup 22
- 1. Speaker Setup 23
- A2 ~ A6 Crossover Frequency 24
- A7 Test Tone 24
- A8 Restore 24
- 2. Input Setup 25
- 3. Option Setup 26
- 1 . S p 2 . I n 3 . O p 27
- O p t i o n S e t u p 27
- 6 R e m o t e I D : 1 27
- Stereo Playback 28
- DSP Simulation Playback 28
- Parameter 29
- A9 Dynamic Volume 32
- S1 RESTORER 32
- O F F S E T - 4 d B 33
- Playback 34
- Playing Video and Audio 35
- Equipment 35
- Listening to FM/AM Broadcasts 35
- Presetting Radio Stations 36
- (Preset Memory) 36
- Listening to Preset Stations 36
- RDS (Radio Data System) 36
- RDS Search 37
- PTY Search 37
- TP Search 37
- RT (Radio Text) 37
- Playback 38
- Listening to Audio 39
- Other Operations 40
- Convenient Functions 40
- <POWER> 41
- Operating DENON Audio 42
- Components 42
- Presetting 42
- Operating Preset Components 42
- Punch Through Function 44
- Other Information 45
- Audyssey 46
- Surround Modes and Parameters 47
- Troubleshooting 50
- TEST button 51
- Television 53
- Satellite Receiver 54
Related products and manuals for Receiver Denon AVR-1509
Receiver Denon AVR-1507 User Manual
(61 pages)
(61 pages)
Receiver Denon AVR-X510BT Owner's Manual
(127 pages)
(127 pages)
Receiver Denon DRA-37 Owner's Manual
(60 pages)
(60 pages)
Receiver Denon AVR-1508 Owner's Manual
(60 pages)
(60 pages)
Receiver Denon RCD-CX1 Owner's Manual
(36 pages)
(36 pages)
Receiver Denon AVR-3805S Operations Instructions
(104 pages)
(104 pages)
Receiver Denon AVR-4810 User Manual
(57 pages)
(57 pages)
Receiver Denon AVR-3808 User Manual
(89 pages)
(89 pages)
Receiver Denon AVR-2807 User Manual
(88 pages)
(88 pages)
Receiver Denon AVR-3808 Owner's Manual
(16 pages)
(16 pages)
Receiver Denon AVC-3890 User Manual
(15 pages)
(15 pages)
Receiver Denon AVR-3313CI User Manual
(52 pages)
(52 pages)
© 2020, manymanuals.com. All rights reserved. | 0.651 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals