Denon AVR 689 - AV Receiver Owner's Manual download pdf (Page 24)

Speciﬁ cations

Step 4 : Check

• To proceed to “Step 5” without checking the analysis result, use u i to select “Store<”

while “Parameter Check<” is displayed.

• Values that are different from the actual distance may be set for speakers with built-in ﬁ lters

(subwoofers, etc). This is because ﬁ lters add electrical delay to the signal that should be

compensated.

NOTE

Do not turn the power off while the settings are being stored.

Step 5 : Store

The auto setup measurement results are stored in the AVR-689.

q Press o while “Store<” is displayed.

• “Storing” blinks on the display panel while the results are being stored.

• When storing is complete, “Completed” is displayed followed by “Disconnect Mic”.

w Disconnect the setup microphone from the AVR-689.

s Error Messages

If the auto setup procedure could not be completed due to speaker installation, the measuring environment,

etc. an error message is displayed. Check the relevant items and be sure to take the necessary measures. After

addressing any issues, perform the auto setup procedure over again.

NOTE

Be sure to turn the power off before checking speaker connections.

Select “Retry” to make the measurements again.

Error messages (examples) Cause Measures

M i c o r S p : N o n e

• The included setup microphone is not

connected.

• Not all speakers could be detected.

• Connect the included setup

microphone to the SETUP MIC jack

on the main unit.

• Check the speaker connections.

A m b i e n t N o i s e

• Too much noise in the room for

accurate measurements to be made.

• Speaker or subwoofer sound is too

low for accurate measurements to be

made.

• Either turn off any device generating

noise or move it away.

• Try again when the surroundings are

quieter.

• Check the speaker installation and the

direction in which the speakers are

facing.

• Adjust the subwoofer’s volume.

C a u t i o n : S p N o n e

The messages alternate

F R

• Displayed speaker could not be

detected.

· The front L and front R speakers

were not properly detected.

· Only one channel of the surround

speakers was detected.

· Sound was output from the R

channel when only one surround

back speaker was connected.

· The surround back speaker was

detected, but the surrounds were

not detected.

• Check the connections of the

displayed speaker.

C a u t i o n : P h a s e

The messages alternate

S B L

• Displayed speaker connected with

the polarities reversed.

• Check the polarities of the displayed

speaker.

• For some speakers, this error

message may be displayed even if the

speaker is properly connected. If the

connection is correct, use the u or i

buttons to display “Skip<” and then

press o.

n To switch to another analysis result item

Press ENTER.

This returns you to analysis results items, so repeat operation q.

n To proceed to “Step 5 : Store”

During display of crossover frequency result or analysis results item, press ENTER.

• “Store<” is displayed.

n To cancel storing

Use u or i to display “Cancel<” while “Store<” is displayed and press o.

• All the measured auto setup data will be erased.

When analysis is complete, “Parameter Check<” is displayed.

Press o and check the analysis results for the following four items.

q Make your selection using ui and press o.

• Presence and size of speaker

“SpConﬁ g. Check<”

• Distance of speaker from listening position

“Distance Check<”

• Speaker channel level

“Ch Level Check<”

• Crossover Frequency

“Crossover Check<”

w Use u or i to change which speaker is displayed.



Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

ENGLISH

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 70 71

Comments to this Manuals

No comments

Denon AVR 689 - AV Receiver Owner's Manual Page 24

Comments to this Manuals

Related products and manuals for Receiver Denon AVR 689 - AV Receiver