Denon AVR-5700 User Manual Page 33

  • Download
  • Add to my manuals
  • Print
  • Page
    / 64
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 32
33
Learning function
If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-5700’s
remote control to “learn” the codes from the component’s original remote control.
The buttons that can be “learned” are the CD, DECK and MD system buttons (see page 29) and the DVD, VDP, VCR and TV system buttons
(see page 32). (For the CD, MD, DVD, VDP and TV, the A block buttons can also be “learned”, and for the DVD and TV, the B block buttons
can also be “learned”.)
1
2
3
4
Press the USE/LEARN selector button with the tip of a pen
etc., to set the learn mode. Both the START and
LEARNED/TX indicators flash.
Set the program switch to the side to be “learned”.
Set to the AUDIO side for the CD, tape deck or DAT position,
to the VIDEO side for the VDP, VCR or TV position.
Set the program switch to the position to be “learned”.
Set the remote control units so they are facing each other,
then press the button to be “learned” on this unit’s remote
control unit.
AVR/AVC VIDEO
AUDIO
DVD TV
VDP VCR
CD
MD
LOCK
DECK
This unit’s remote
control unit
Flashes
DVD
HOME THX CINEMA
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
USE/LEARN T.TONE MULTI DVD
SET UP
RETURN
PANEL
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
VDP TUNER SHIFT
TV/DBS V.AUX PHONO
VCR-1 CD
MD
/
TAPE-1
CHANNEL
VCR-2
TAPE-2 MON
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MD
LOCK
DECK
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
A
2
4
3
B
1,8
Lit
This unit’s remote
control unit
Approx.
5 cm
Other remote
control unit
Transmitting windows
The indicator stops flashing and the START LED lights.
The learnable buttons are the buttons which can be operated
with the DENON system codes for the CD player, DAT and
tape deck, the buttons which can be operated with the
preset memory for the VCR, VDP and TV. For the TV only,
however, the buttons in the section indicated “A” on the
diagram above can also be “learned”. Use these to “learn”
TV channels.
5
6
7
8
Check that the START LED is lit, then press the button to be
“learned” on the other remote control unit.
Once the START LED turns off and the LEARNED/TX LED
lights, release the button on the other remote control unit.
To “learn” other buttons, repeat steps 2 to 6.
Once the learning operation is completed, press the
USE/LEARN selector button again.
The two LEDs stop flashing and the learning mode is
cancelled.
The two LEDs start
flashing again.
Lit
Check that the stored
codes work properly.
NOTES:
Up to 26 codes can be “learned”, but this number may be lower if the codes are long.
If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s)
is released.
If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models,
codes cannot be stored in RC-853.
If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just
attempted to store was not stored.
To “learn” that code, first perform the resetting operation. (See page 36.)
This unit’s remote
control unit
Other remote
control unit
Page view 32
1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 63 64

Comments to this Manuals

No comments