Denon AVR 1909 - AV Receiver Owner's Manual Page 30
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Specifications
Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting
ENGLISH
Step 2 : Measurement
q Press u to select “Next
0
”, then press o.
• The measurement of the 2nd position starts.
w Move the microphone to the 3rd position and press o.
• The measurement of the 3rd position starts.
e Perform w repeatedly for the 4th, 5th, and 6th measurments.
• “All the measurements were finished.” is displayed on the on-
screen display. When you have completed measurements in 6
positions.
• If you want to stop after measuring just five or fewer positions,
press i to select “Cancel
0
”, then press o.
After completing a measurement position, move the microphone to
the next position.
Measure at 6 positions: the main listening position and 5 other
surrounding positions. Although it is allowable to measure less than 6
positions, it is recommended to measure 6 for best results.
Step 3 : Calculation
The values obtained from the measurements are automatically
analyzed and the attributes for each of the speakers in the listening
area are determined.
q Press u to select “Calculate
0
”, then press o.
• Analysis begins.
• Analysis takes several minutes to complete.
• The time required for this analysis depends on the number of
speakers connected. The greater the number of speakers connected,
the longer analysis will take.
NOTE
• Do not change the speaker connections or subwoofer volume,
or speaker locations after making measurements. If changes are
necessary, make the changes and use the Audyssey MultEQ auto
setup once again for an updated EQ solution.
• For instance, if the location or direction of a speaker is altered, the
Auto Setup should be performed again to ensure the correct EQ
solution for the new room configuration.
F Menu screen F
q
w
Auto Setup
Step2:Measurement
Audyssey
MultEQ
Please place microphone
Cancel
Next
Calculate
2nd listening position.
at ear height at
Auto Setup
Step2:Measurement
Audyssey
MultEQ
Now measuring 2nd
Cancel
Front L
listening position.
e
Auto Setup
Step2:Measurement
Audyssey
MultEQ
Please place microphone
Retry
Cancel
Next
Calculate
3nd listening position.
at ear height at
Step 4 : Check
Distance values that are greater than the actual distance of a speaker
may be accurate for speakers with built-in filters (subwoofers, etc).
This is because these filters add electrical delay (distance) to the signal
that is compensated for by the Auto Setup process.
n To switch to another analysis result item
Press RETURN.
This returns you to analysis results items, so repeat step q.
n To proceed to “Step 5 : Store”
Press u to select “Next
0
”, then press o.
When analysis is complete, check the analysis results for the following
four items.
q Make your selection using ui and press ENTER.
• Presence and size of speaker
“Speaker Config. Check”
• Distance of speaker from listening position
“Distance Check”
• Speaker channel level
“Channel Level Check”
• Crossover Frequency
“Crossover Freq. Check”
w Use ui to change which speaker is displayed.
F Menu screen F
q
Auto Setup
Step4:Check
Audyssey
MultEQ
Please check the results
of the measured item.
Distance Check
Channel Level Check
Crossover Freq.Check
Speaker Config.Check
Next
F Menu screen F
q
Auto Setup
Step2:Measurement
Audyssey
MultEQ
Retry
Cancel
Calculate
All the measurements
were finished.
Auto Setup
Step3:Calculation
Audyssey
MultEQ
Calculating
––––––––––––––––––––––––––––––––––––
Please wait...
- AVR-1909 1
- SAFETY INSTRUCTIONS 2
- ENGLISHFRANCAIS 3
- Accessories 5
- Cautions on Handling 6
- Cautions on Installation 6
- About the Remote Control Unit 6
- Part Names and Functions 7
- Rear Panel 9
- Remote Control Unit 10
- Preparations 11
- Video Conversion Function 12
- Speaker Connections 13
- Specifications 14
- Connections 15
- Connecting the Monitor 16
- CD Player 17
- TV/CABLE Tuner 18
- Video Cassette Recorder 18
- Connections to Other Devices 19
- XM connector 20
- SIRIUS connector 21
- Antenna terminals 22
- Multi-zone 23
- External Controller 23
- Connecting the Power Cord 24
- Menu Operations 25
- Menu Map 27
- Auto Setup 28
- Step 2 : Measurement 30
- Step 3 : Calculation 30
- Step 4 : Check 30
- Error Messages 31
- Speaker Setup 32
- Test Tone 34
- Test Tone Start 34
- HDMI Setup 35
- Audio Setup 36
- ZONE2 Setup 37
- Option Setup 38
- Setup Lock 40
- Input Setup 41
- Resolution 43
- Progressive Mode 43
- Component In 45
- Digital In 45
- A1 Parental Lock 46
- A0 Antenna Aiming 46
- Surround Modes 47
- Direct Playback 48
- Stereo Playback 48
- Adjusting the parameters 49
- Surround Parameter 50
- Audyssey Settings 52
- S2 Dynamic EQ 53
- S3 Dynamic Volume 53
- RESTORER 54
- Night Mode 54
- Audio Delay 54
- Audio Input Signal 55
- HDMI Information 56
- Auto Surround Mode 56
- Preset Station 56
- Quick Select 56
- Listening to FM/AM Broadcasts 58
- Playing Video and Audio 58
- Equipment 58
- Programs 59
- S R 000 S i r iu s I D 61
- * * *** * * * * ** * 61
- Playback 62
- Listening to Music 63
- Other Operations 64
- Convenient Functions 65
- Fader Function 66
- Channel Level 66
- Playback 67
- Main Remote Control Unit 68
- (RC-1099) 68
- Remote Control 69
- Sub Remote Control Unit 71
- (RC-1107) 71
- Setting 1 : 72
- Setting 2 : 73
- Setting 3 : 73
- ZONE2 ZONE2 OUT Stereo 74
- Multi-zone Operations 75
- About Speaker Installation 76
- Surround 77
- Neural Surround 78
- Audyssey 78
- Surround Modes and Parameters 79
- MENU button on 84
- Troubleshooting 85
- TEST button is 86
- On-screen 87
- Television 90
- Satellite Receiver 91
Related products and manuals for Telephones Denon AVR 1909 - AV Receiver
(81 pages)
Telephones Denon AVR-789 Service Manual
(161 pages)
(161 pages)
© 2020, manymanuals.com. All rights reserved. | 2.741 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals