Denon AVP-A1HDCI User Manual download pdf (Page 11)

GUI Menu Map Setup Information TroubleshootingPlayback

The strength of both the SIRIUS satellite and terrestrial signals can

be checked at GUI menu “Source Select” – “SIRIUS” – “Antenna

Aiming” (vpage 6).

Checking the SIRIUS Signal Strength

and Radio ID

Either turn <SOURCE SELECT> or press [SAT TU] to

select “SIRIUS”.

b When operating via the remote control unit, you cannot select

SIRIUS even by pressing [SOURCE SELECT] to which SIRIUS has

been assigned.

Press <STATUS> until “SIGNAL” appears on the

display.

The display will switch as shown below, depending on the

reception conditions.

Display Status

EXCELLENT Signal strength is excellent

GOOD Signal strength is good

WEAK Signal strength is weak

NO SIGNAL No signal

Adjust the position of the antenna until “SIGNAL:

EXCELLENT” is shown on the display.

Press <STATUS> until the channel (example: “SR001”)

is displayed.

Press [ ] and select channel 0 (SR000).

Channel No. and Sirius ID are alternately shown on the display.

S R 0 0 0 S i r i u s I D

* * * * * * * * * * * *

b Write your own SIRIUS ID for storage use.

Sirius ID :

Sirius ID

Listening to Preset Channels

Press [CHANNEL + –].

A pop-up window appears.

Select a preset channel using [CHANNEL + –].

Press [ENTER].

Operation on the Main Remote control Unit

Operation on the Main Unit

Press <TUNING PRESET>, then turn <SOURCE SELECT>

to select the preset channel.

Press [A ~ G] to select the block in which the channel

is to be preset.

Press [CHANNEL + –] or [NUMBER (1 ~ 8)] to select

the preset number.

Press [MEMO] again to complete the setting.

To preset other channels, repeat steps 1 to 5.

NOTE

Preset channels are erased by overwriting them.

Presetting Radio Channels

(Preset Memory)

Your favorite broadcast channels can be preset so that you can

tune them in easily. Up to 56 channels can be preset.

Tune in the broadcast channel you want to preset.

Press [MEMO].

Searching Categories

Press o p.

S R 0 0 1 H i t s 1

C A T : P o p s

Use o p to select the category, to use ui to select

the desired channel.

Channel category

Selection is still possible if you press [0 ~ 8] after pressing [A ~ G].

Make the necessary preparations.

q Assign the SIRIUS input.

Assign the SIRIUS input.

: ”Source Select” – “(input source)” – “Assign”–

”SIRIUS” (vpage 7)

w Change the TUNER(DEV2) setting on the main remote control unit

to SIRIUS.

: ”Manual Setup” – “Option Setup” –

”Remote (SIRIUS/XM)” (vpage 5)

Either turn <SOURCE SELECT> or press [SAT TU] to

select “SIRIUS”.

b When operating via the remote control unit, you cannot select

SIRIUS even by pressing [SOURCE SELECT] to which SIRIUS has

been assigned.

When using the main remote control unit to operate,

press [TU] to select mode.

Use [ ] to select the channel.

When the channel is tuned in, the name of the song and artist

are displayed.

• The channel switches continuously when [ ] is pressed

and held.

• The song title, artist name, composer name, category and reception

level can be checked by pressing <STATUS>.

• The time (default : 30 sec) for which the on-screen display are

displayed can be set at GUI menu “Manual Setup” – “Option Setup”

– “GUI” – “Tuner”.

• The sub remote control unit can also be used for SIRIUS (vpage

12).

Basic Operation

There is no SIRIUS-dedicated input terminal for AVP-A1HDCI /

AVR-5308CI.

When using an audio input source not used by AVP-A1HDCI /

AVR-5308CI, assign SIRIUS to the source.

1.AVP-A1HDCI_AVR5308CI_2nd.indd 11 2008/09/03 9:22:55

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Denon AVP-A1HDCI User Manual Page 11

Comments to this Manuals

Related products and manuals for Acoustics Denon AVP-A1HDCI