Denon AVR-882 Operations Instructions Page 27

  • Download
  • Add to my manuals
  • Print
  • Page
    / 96
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 26
3
Select the play mode.
Press the SURROUND MODE button, then turn SELECT
knob.
SURROUND SURROUND
MODE SELECT MODE
% o %
(Main unit) (Remote control unit)
•_ To select the surround mode while adjusting SURROUND
the surround parameters, channel volume or MODE
tone control, press the surround mode
button then operate the selector.
(Main unit)
4
Start playback on the selected component.
For operating instructions, refer to the component's
manual.
Adjust the volume.
MASTER VOLUME
The volume level is (Main unit) (Remote control unit)
displayed on the
master volume level
display.
•_ The volume can be adjusted within the range of -60 to 0 to 18 dB,
in steps of 1 dB. However, when the channel level is set as
described on page 30, if the volume for any channel is set at +1 dB
or greater, the volume cannot be adjusted up to 18 dB. (In this case
the maximum volume adjustment range is "18 dB -- (Maximum
value of channel level)".)
Input mode when playing DTS sources
Noise will be output if DTS-compatible CDs or LDs are played in the
"ANALOG" or "PCM" mode.
When playing DTS-compatible sources, be sure to connect the
source component to the digital input jacks (OPTICAL/COAXIAL)
and set the input mode to "DTS'.
Input mode display
In the AUTO mode
_NPUT
AUTO PCM OTS
_ o o
In the DIGITAL PCM mode
INPUT
AUTO P_M z DTS
O _@C O
In the DIGITAL DTS mode
INPUT
AUTO PCM DTS
o o _'o
In the ANALOG mode
iNPUT
AUTO PCM DTS
O O O
One of these lights, depending on the
input signal.
Input signal display
DOLBY DIGITAL
_ S+GNAL
D+GtTAL
_'p. o
DTS
_ S+GNAL
DIGITAL
o _e
PCM
_ S+GNAL
DIGITAL
O O
•_ The _ indicator lights when digital signals are being input
properly. If the _ indicator does not light, check whether
the digital input component setup (page 21) and connections are
correct and whether the component's power is turned on.
NOTE:
The _ indicator will light when playing CD-ROMs
containing data other than audio signals, but no sound will be
heard.
[1] Adjusting the sound quality (tone)
1
The tone switches as follows each time TONE CONTROL is
pressed.
TONE
CONTROL
%
BASS_TREBLE
(Main unit)
2
With the name of the volume to be
adjusted selected, turn SELECT knob to
adjust the level.
SELECT
O
To increase the bass or treble: Turn
the control clockwise. (The bass or (Mainunit)
treble sound can be increased to up
to +12 dB in steps of 2 dB.)
To decrease the bass or treble: Turn the control
counterclockwise. (The bass or treble sound can be
decreased to up to -12 dB in steps of 2 dB.)
3
DENON
_ O o °
o _[_) o o o o o o o o o o o
D O _ ..... 1 _ _=_t_ z
3 2 1
If you do not want the bass and treble to be adjusted, turn on
the tone defeat mode.
TONE DEFEAT
•_ The signals do not pass through the
bass and treble adjustment circuits,
providing higher quality sound.
(Main unit)
27
Page view 26
1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 95 96

Comments to this Manuals

No comments