Denon AVR3310CI - Multi-Zone Home Theater Receiver Owner's Manual download pdf (Page 14)



Connections Settings Information SpeciﬁcationsGetting Started Unavailable Functions After Upgrading

ENGLISH

Setting items Setting contents

Surround Parameters

(Continued)

This can also be set by pressing STANDARD.

If the source being played contains a surround back signal, the decoder

type is automatically selected by the AFDM function. Set “AFDM” to

“OFF” to switch to your preferred decoder.

If the setting in “Speaker Conﬁguration” – “Surround Back” (vpage 9)

is “None”, “Surround Back” is not displayed.

•

Subwoofer Att. : Attenuate subwoofer level when using EXT. IN input.

ON : Set.

OFF : Do not set. Usually use in this mode.

Set this to “ON” if the subwoofer channel level seems too high when

playing audio signal.

•

Subwoofer : Turn subwoofer output on and off.

ON : The subwoofer is used.

OFF : The subwoofer is not used.

•

Default : Restores all the surround parameter settings to their defaults.

No : Do not reset to the defaults.

Yes : Reset to the defaults.

•

Tone

Adjust the tonal quality of

the sound.

Tone Control : Sets the tone control function ON and OFF.

ON : Allow tone adjustment (treble, bass).

OFF : Playback without tone adjustment.

This can be set when “Dynamic EQ” (vpage 14) is set to “OFF”.

The tone cannot be adjusted in the direct mode.

•

Bass : Adjust low frequency range (bass).

–6dB ~ +6dB

This can be set when “Tone Control” (vpage 13) is set to “ON”.

•

Treble : Adjust high frequency range (treble).

–6dB ~ +6dB

This can be set when “Tone Control” (vpage 13) is set to “ON”.

•

Setting items Setting contents

Audyssey Settings

Set Audyssey MultEQ

Audyssey Dynamic EQ

and Audyssey Dynamic

Volume™.

NOTE

If you have not performed

Auto Setup, or if you

change the speaker

settings after performing

Auto Setup, you may not

be able to select Dynamic

EQ/Dynamic Volume, and

“Run Audyssey” may be

displayed.

In this case, either perform

Audyssey Auto Setup over

again or perform “Restore”

(vpage 33 of GThe

original versionH Operating

Instructions) to return to

the settings after Audyssey

Auto Setup was run.

MultEQ : Corrects both time and frequency response problems in the

listening area.

Audyssey : Optimize the frequency response of all speakers.

Audyssey Byp.L/R : Optimize frequency response of speakers except

front L and R speakers.

Audyssey Flat : Optimize frequency response of all speakers to ﬂat

response.

Manual : Apply frequency response set with “Manual EQ” (vpage

16).

OFF : Turn “MultEQ” equalizer off.

“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be

selected after Audyssey Auto Setup has been performed. “Audyssey”

is automatically selected after performing Audyssey Auto Setup. “When

“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected, “ ”

lights.

After running Audyssey Auto Setup, if the Speaker Conﬁguration,

Distance, Channel Level, and Crossover Frequency have changed without

increasing the number of speakers measured, only “ ” lights.

If “Dynamic EQ” or “Dynamic Volume” is set to “ON” when “MultEQ”

is set to either “OFF” or “Manual”, “MultEQ” is automatically set to

“Audyssey”.

You can also press MULTEQ to set.

NOTE

“MultEQ” and “Manual EQ” cannot be selected when “EQ Customize”

is set to “Not Used” (vpage 38 of GThe original versionH Operating

Instructions).

When using headphones, “MultEQ” is set to “OFF”.

•

Adjusting the Sound and Picture Quality (Audio/Video Adjust)

Playback

Main remote control

operation buttons

:Displaying the menu

Cancel the menu

:Moves the cursor

(Up/Down/Left/Right)

:Conﬁrm the setting :Return to previous menu

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Comments to this Manuals

No comments

Denon AVR3310CI - Multi-Zone Home Theater Receiver Owner's Manual Page 14

Comments to this Manuals

Related products and manuals for AV receivers Denon AVR3310CI - Multi-Zone Home Theater Receiver