Denon 2010CI - DBP Blu-Ray Disc Player Owner's Manual download pdf (Page 10)

7

Introduction Introduction

ENGLISH

ENGLISH

Introduction Connections Playback Function Setup Others

The unit can also be turned on by pressing the buttons with circled numbers.

Part Names and Functions

Front Panel

ON / STANDBY

SD CARD

9

5

643 7 8

2

1

11

10 12 13

1. Power indicator

This indicator lights up in green when the

power is on, and lights up in red in standby

mode.

2. ON/STANDBY button

Press to turn on the unit, or to turn the unit

to the standby mode. (In standby mode, this

unit still consumes small amount of power.

To completely shut down the unit, you must

unplug the AC cord.)

3. Infrared sensor window

Receives signals from your remote control so

that you can control the unit from a distance.

4. Display

Refer to “Front Panel Display” on page 9.

5. SD CARD slot

Insert an SD Memory Card, and play back the

contents in it.

6. HDMI RESOLUTION button

Press to set the HDMI jack’s video signal

output mode.

7. F (STILL/PAUSE) button

Press to pause playback.

8. h / g (FAST FORWARD/REVERSE)

button

Press to search forward / backward through

a disc.

9. Disc tray

Place a disc when opening the disc tray.

10. A (OPEN/CLOSE) button

Press to open or close the disc tray.

11. B (PLAY) button

Press to start or resume playback.

12. C (STOP) button

Press to stop playback.

13. H / G (SKIP DOWN/UP) button

Press to skip down/up titles/chapters/tracks/

files.

Rear Panel

HDMI OUT

ETHERNET

AC IN

COAXIAL

COMPONENT VIDEO OUT VIDEO OUT

DIGITAL OUT

( PCM / BITSTREAM )

ROOM TO ROOM

REMOTE CONTROL

RS-232C

STRAIGHT CABLE

2ch AUDIO OUT

L

SBR

FR

SW

7.1ch AUDIO OUT

C

FL SL SBL

SR

R

2 3 41 5

1098

76

1. AC Inlet (AC IN)

Use to connect the AC cord to supply the

power.

2. DIGITAL OUT (COAXIAL) jack

Use digital audio coaxial cable to connect to

an AV receiver, Dolby Digital decoder or

other device with a digital audio coaxial

input jack.

3. COMPONENT VIDEO OUT jacks

Use a component video cable to connect to

a display device with component input jacks.

4. VIDEO OUT jack

Use an RCA video cable to connect to a TV

monitor, AV receiver or other device.

5. REMOTE CONTROL IN / OUT jacks

Connecting the DENON Satellite Remote

Control to these jacks enables you to

operate more than one DENON components

with one remote control.

6. 2ch AUDIO OUT jacks

Use an RCA audio cable to connect these

jacks to the 2-channel audio input jacks of

your amplifier with 2- channel input

terminals.

7. 7.1ch AUDIO OUT jacks

Use an RCA audio cable to connect these

jacks to the 7.1-channel audio input jacks of

your amplifier with 7.1-channel input

terminals.

8. ETHERNET Terminal

Use to connect a telecommunications

equipment with LAN cable.

9. HDMI OUT jack

Use an HDMI cable to connect to a display

with an HDMI input jack.

10. CONTROL CONNECTOR (RS-232C)

This is a terminal for future system extension.

Note

• Do not touch the inner pins of the jacks on

the rear panel. Electrostatic discharge may

cause permanent damage to the unit.

E5KA0UD_EN.book Page 7 Tuesday, April 28, 2009 11:15 AM

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 51 52

Comments to this Manuals

No comments