Denon AVR-890 User Manual download pdf (Page 56)



ENGLISH

Getting Started Connections Remote Control Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings

Press .

Press ui to select the speaker.

The speaker that can be set switches each

time one of the buttons is pressed.

Press o p to adjust the volume.

b In the case of a subwoofer, reducing the volume when it is at “–12

dB” will change the setting to “OFF” (none).

C H A N N E L L E V E L

Bd0.0LtnorF

Bd0.0retneC

Bd0.0RtnorF

Bd0.0refoowbuS

Bd0.0RdnuorruS

Bd0.0RkcaB.S

Bd0.0LkcaB.S

Bd0.0LdnuorruS

raeRtnorFredaF

S e l e c t

Use or i to select “Fader”, then select the item

to be adjusting using o or p.

Press o p to adjust the volume of the speakers.

• The fader function does not affect the subwoofer.

• The fader can be adjusted until the volume of the speaker adjusted

to the lowest value is –12 dB.

Set the items below to the settings you want to save.

q Input source (vpage 40)

w Input Mode (vpage 37)

e Surround Mode (vpage 44)

r Audyssey Settings (MultEQ

, Dynamic EQ™, Dynamic

Volume™) (vpage 48)

t Front Speaker Setup (vpage 29)

y Volume setting (vpage 40)

u Video select (vpage 36)

Press and hold the desired until “Memory”

appears on the display.

The current settings will be memorized.

NOTE

Input sources stored with the quick select function cannot be selected

if they have been deleted at menu “Source Delete” (vpage 32). In

this case, store them again.

Adjust the Volume of the

Different Speakers

You can adjust the channel level either according to the playback

sources or to suit your taste, as described below.

Saving Frequently Used Settings

(Quick Select Function)

This function allows you to save all the settings shown in step

1. When frequently used settings are saved, they can easily be

set again the next time you want to use them. This function also

allows you to always enjoy the same playback environment.

• Three sets of settings can be saved.

Saving the settings

Press the at which the

settings you want to call out are saved.

Calling the settings out

This function lets you adjust (fade) the sound from all the front (Front

speaker / center speaker / Front Height speaker) or rear (Surround speaker /

Surround Back speaker) speakers at once.

If headphones are plugged in, the headphones settings screen

appears.

The surround parameters, tone settings and the volumes of the

different speakers are stored for the individual surround modes.

GQuick Select DefaultsH

Input Source Volume

Quick Select 1 DVD –40 dB

Quick Select 2 SAT/CBL –40 dB

Quick Select 3 VCR/iPod –40 dB

n Naming Quick Select settings

“Quick Select Name” (vpage 33).

Various Memory Functions

Adjust the volume of the different speakers

Adjusting the volume of groups of speakers

(Fader Function)

Personal Memory Plus Function

This function sets the settings (input mode, surround mode, HDMI

output mode, MultEQ, Dynamic EQ, Dynamic Volume, audio delay

etc.) last selected for the individual input sources.

Last Function Memory

This stores the settings as they were directly before the standby mode

was set.

When the power is turned back on, the settings are restored to as they

were directly before the standby mode was set.

Backup Memory

The various settings are backed up for about 1 week, even if the power

is turned off or the power cord is disconnected.

Saving the settings

It is also possible to save three settings for ZONE2.

Set the remote control unit’s

device selector switches as

shown on right.

 Perform steps 1 and 2 under “MAIN ZONE

settings”.

MAIN ZONE settings

ZONE2 settings

Front

Playback

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 75 76

Comments to this Manuals

No comments

Denon AVR-890 User Manual Page 56

Comments to this Manuals

Related products and manuals for Home Theater Systems Denon AVR-890