Denon AVR 589 - AV Receiver Owner's Manual Page 41

  • Download
  • Add to my manuals
  • Print
  • Page
    / 58
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 40
iPod
®
Playback
The music on an iPod can be played by using the control dock for
iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W, sold separately).
The operation can also be performed using the buttons on the
remote control unit.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
b The iPod may only be used to copy or play contents that are not
copyrighted or contents for which copying or playback is legally
permitted for your private use as an individual. Be sure to comply
with applicable copyright legislation.
4
Press [MODE] and hold it down for a 2 seconds or
more to select the display mode.
To switch between modes, press and hold down the button.
When remote mode is active, “Remote” is displayed.
[Selectable mode]
Browse mode Remote mode
Display location Main unit display
iPod display
Playable
files
Audio file
S S
Video file
S
z1
S
z2
Active
buttons
Remote
control unit
(AVR-589)
S S
iPod
A S
z1 :
When using an ASD-3N or ASD-3W control dock for iPod.
z2 :
Video may not be output, depending on the combination of
ASD-1R or ASD-11R and iPod.
With the default settings, the iPod can be used connected to the VCR
(iPod) connector.
Use the RESTORER mode to expand the low and high frequency
components of compressed audio files and achieve a richer sound.
The default setting is “Mode3” (vpage 32).
Press <ON/STANDBY> or [OFF] and set the AVR-589’s power to
the standby mode before disconnecting the iPod. Also switch the
input source to one to which “iPod Assignis not assigned before
disconnecting the iPod.
When using an ASD-3N or ASD-3W control dock for iPod, refer to the
respective manual to operate.
1
Make the necessary preparations.
q Set the iPod in the DENON control dock for iPod.
(vSee the control dock for iPod’s operating instructions.)
w Assign the control dock for iPod’s input.
The input for the control dock for iPod is assigned to VCR by
default.
“System Setup” “Input Setup” “iPod Assign”
(vpage 24)
2
Either turn <SOURCE SELECT> or press [iPod] to
select the input source assigned in step 1-w above.
3
Set [SOURCE CONTROL 1] to “AUDIO” and [SOURCE
CONTROL 2] to “iPod/NETWORK”.
(v page 42 “Remote Control Unit Operations”)
Preparations
Searching Categories
1
Press [o p].
C A T E G O R Y S E A R C H
C A T : P o p s
2
Use [o p] to select the category, then use [ui] to
select the desired channel.
Channel category
“UPDATING” is displayed while the encording code is being
updated.
“SIRIUS UPDATING” is displayed when updating SIRIUS tuner
firmware.
Refer to “Troubleshooting” (vpage 52) regarding other messages.
Parental Lock
Channels under Parental Lock cannot be tuned in by performing
Tuning Up/Down or by category search.
Channels stored in preset memory can be tuned in by the preset
channel select operation, even if Parental Lock is applied.
When a channel to which Parental Lock is applied is being played,
Parental Lock for that channel is cancelled by performing Step 2.
See “Edit Lock Cord” (vpage 25) for the method of changing
Parental Lock Cord.
You can also set “Parental Lock” from the system setup (vpage
25).

Getting Started Connections Setup Playback Remote Control Information Troubleshooting
ENGLISH
Specifications
1
Tune to the channel you want to lock.
2
Press [ENTER] for at least 3 seconds.
“Code: [ ]” is displayed.
3
Enter the 4-digit lock code using uiop.
When you enter the correct code, the corresponding channel is
locked.
4
Press [ENTER].
Page view 40
1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 57 58

Comments to this Manuals

No comments