Denon AVR-789 User Manual Page 48
- Page / 95
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Specifications
A4 SB CH Out
(Selectable displays during 2-channel source playback.)
Determine whether to use surround back speakers.
[Selectable items]
ON
: The surround back channel signal is played.
OFF
: The surround back channel signal is not played.
A5 SUBWOOFER ATT
Attenuate subwoofer level when using EXT. IN mode.
[Selectable items]
ON
: The input from the subwoofer channel is attenuated.
OFF
: The input from the subwoofer channel is not attenuated.
Usually use in this mode.
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
A6 Subwoofer
Turn subwoofer output on and off.
[Selectable items]
ON
: The subwoofer is used.
OFF
: The subwoofer is not used.
Tone
Adjust the tonal quality of the sound.
Audyssey Settings
Select MultEQ, Dynamic EQ and Dynamic Volume.
Audyssey
Audyssey Byp. L/R
Audyssey Flat
ManualOFF
S0 MultEQ
Select the type of correction desired from the following list:
[Selectable items]
Audyssey
: Optimize frequency response of all speakers.
Audyssey Byp. L/R
: Optimize frequency response of speakers
except front L and R speakers.
Audyssey Flat
: Optimize frequency response of all speakers
to flat response.
Manual
: Apply frequency response set with “Manual
EQ” (vpage 30).
OFF
: Turn equalizer off.
Operating from the main unit or remote control
unit
Press MULTEQ.
A7 Tone Control
Turn tone adjustments off.
[Selectable items]
ON
: Allow tone adjustment (treble, bass).
OFF
: Playback without tone adjustment.
The tone cannot be adjusted when in the DIRECT mode.
A8 Bass
Adjust low frequency range (bass).
[Variable range]
–6dB
~
0dB
~
+6dB
A9 Treble
Adjust high frequency range (treble).
[Variable range]
–6dB
~
0dB
~
+6dB
“Bass” and “Treble” can be set when “Tone Control” is set to “ON”.
NOTE
When the “Dynamic EQ” setting is “ON”, setting is not possible.
• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is
selected, “ ” lights.
• After running Auto Setup, if the Speaker Configuration, Distance,
Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only “ ”
lights.
• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
selected after the auto setup procedure has been performed.
• After performing “Auto Setup”, the “MultEQ” setting automatically
becomes “Audyssey”.
• If the settings of speakers for which “None” has been determined
at “Auto Setup” are changed, “Audyssey”, “Audyssey Byp. L/R” and
“Audyssey Flat” cannot be selected. Either perform Auto Setup
again, or return to the setting after running Auto Setup with “Auto
Setup” – “Parameter Check” – “Restore”.
• MultEQ and Manual EQ set to “Not Used” with “Manual Setup”
– “Audio Setup” – “EQ Preset” – “EQ Customize” (vpage 30) on
the menu, cannot be selected.
• When using headphones, “MultEQ” is set to “OFF”.
For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 42).
Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting
ENGLISH
- AV SURROUND RECEIVER 1
- SAFETY INSTRUCTIONS 2
- ENGLISHFRANCAIS 3
- Accessories 5
- Cautions on Handling 6
- Cautions on Installation 6
- About the Remote Control Unit 6
- Part Names and Functions 7
- Getting Started 8
- Rear Panel 9
- Remote Control Unit 10
- Preparations 11
- Speaker Connections 12
- SpecificationsConnections 14
- Connecting the Monitor 15
- Connecting the Recording 16
- Components 16
- Connections to Other Devices 17
- XM connector 18
- SIRIUS connector 18
- Antenna terminals 19
- Connecting the Power Cord 20
- Menu Operations 21
- Menu Map 23
- Auto Setup 24
- Step 2 : Measurement 26
- Step 3 : Calculation 26
- Step 4 : Check 26
- Error Messages 27
- Speaker Setup 28
- Specifications 29
- Test Tone 30
- Test Tone Start 30
- HDMI Setup 31
- Audio Setup 32
- ZONE2 Setup 33
- Option Setup 34
- Setup Lock 36
- Input Setup 37
- Resolution 39
- Progressive Mode 39
- Component In 41
- Repeat Mode 41
- Digital In 41
- A1 Parental Lock 42
- A0 Antenna Aiming 42
- Surround Modes 43
- Direct Playback 44
- Stereo Playback 44
- Adjusting the parameters 45
- Surround Parameter 46
- Audyssey Settings 48
- S1 Dynamic EQ 49
- S2 Dynamic Volume 49
- S3 Setting 49
- RESTORER 50
- Night Mode 50
- Audio Delay 50
- Audio Input Signal 51
- HDMI Information 52
- Auto Surround Mode 52
- Preset Station 52
- Quick Select 52
- Listening to FM/AM Broadcasts 54
- Playing Video and Audio 54
- Equipment 54
- Programs 55
- S R 00 0 S i ri u s I D 57
- * * ** * * * * ** * * 57
- Playback 58
- Listening to Music 59
- Other Operations 60
- Convenient Functions 61
- Fader Function 62
- Channel Level 62
- Playback 63
- Operating DENON Audio 64
- Presetting 64
- Operating Preset Components 64
- Remote Control 65
- Punch Through Function 67
- Setting 1 : 68
- Setting 3 : 69
- Setting 2 : 69
- ZONE2 ZONE2 OUT Stereo 70
- Multi-zone Operations 71
- About Speaker Installation 72
- Surround 73
- Neural Surround 74
- Audyssey 74
- Surround Modes and Parameters 75
- MENU button on 80
- Troubleshooting 81
- TEST button 82
- SOURCE CONTROL 82
- On-screen 83
- DVD Player 86
- Blu-Ray Disc Player 86
- Television 86
- CD Player 87
- Satellite Receiver 87
- HORIZON MCS 100 89
- Important Safety Instructions 90
- (1) Center Channel speaker 91
- Subwoofer 91
- (4) Satellite speakers 91
- TRIGGER OUT 92
- Subwoofer Controls 93
- Operation 93
- Maintenance and Service 93
- Limited Warranty 94
- If Service Seems Necessary 94
Related products and manuals for Receivers and Amplifiers Denon AVR-789
(90 pages)© 2020, manymanuals.com. All rights reserved. | 0.580 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals