Denon 2310CI - AVR AV Receiver Owner's Manual download pdf (Page 57)



ENGLISH

Getting Started

Connections Remote Control Information Troubleshooting

Speciﬁ cationsMulti-ZoneSettings

Turn the power on for all the equipment connected by

HDMI cable.

Set the HDMI control function for all equipment

connected by HDMI cable.

Set “HDMI Control” (vpage 31) to “ON“.

b Please refer to the owner’s manual as regards setting of connected

devices.

b Carry out Steps 1 and 2 should any of the equipment be

unplugged.

Switch the television input to the HDMI connected to

the AVR-2310CI.

Switch the AVR-2310CI input to the HDMI input

source and check if the picture from the player is ok.

When you turn the TV’s power to standby, check that

the power of the AVR-2310CI and player also goes on

standby.

If the HDMI control function does not operate properly, check the

following points.

• Is the TV or player compatible with the HDMI control function?

• Is the AVR-2310CI properly set?

• Is “HDMI Control” (vpage 31) set to “ON”?

• Is “Power Off Control” (vpage 31) set to “ON”?

• Are the HDMI control function settings of all equipment correct?

NOTE

Should any of the operations below be performed, the interlocking

function may be reset, in which case, repeat step’s 1 and 2.

Menu “HDMI” (vpage 31) setting has changed.

There is a change to the connection between the equipment and the

HDMI, or an increase in equipment.

•

NOTE

• When you power off AVR-2310CI, the HDMI control function does

not operate.

• Some functions may not operate depending on the connected

TV or player. Check the owner’s manual of each device for details

beforehand.

• When “HDMI Control” is set to “ON”, it is not possible to assign an

HDMI terminal to “TV” at “HDMI” (vpage 31).

• When “HDMI Control” (vpage 31) is set to “ON”, power is supplied

constantly to the AC outlet (UNSWITCHED).

Convenient functions

When you make an HDMI connection with a TV or player

compatible with AVR-2310CI and HDMI control functions, you

can perform the following operations by setting the HDMI control

function of each device.

Press and display the time you want to set.

The “SLEEP” indicator on the display lights.

• The time switches as shown below each time is

pressed.

Sleep:OFF Sleep:120min

Sleep:30min Sleep:60min

Sleep:90min

• The time display turns off after about 5 seconds, and the

setting is activated.

• Once the set time has passed, the power is automatically set

to standby.

This function allows you to automatically set the power to standby

after the set amount of time has passed.

When the sleep timer turns the power off in the MAIN ZONE, the

power also turns off in the ZONE2.

HDMI Control Function

Setting the Power to Standby

After a Certain Amount of Time

(Sleep Timer Function)

n To cancel the sleep timer

Press to set “OFF”.

• The “SLEEP” indicator on the display turns

off.

• To play the TV’s sound on the AVR-2310CI, make optical digital

connections (vpage 14 “Connecting the monitor (TV)”).

• To use this function, set “HDMI Control” (vpage 31) to “ON”.

Rear

n AVR-2310CI power off can be linked to the TV

power off step

zWhen you set “Output audio from amp” in the TV audio

output setup operation, you can switch the amp power

on.

n You can switch audio output devices with a TV

operation

n You can adjust AVR-2310CI volume in the TV

volume adjustment operation

n You can switch AVR-2310CI input source through

linkage to TV input switching

n When playing the player, the AVR-2310CI input

function switches to the function of that player

Playback

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 77 78

Comments to this Manuals

No comments

Denon 2310CI - AVR AV Receiver Owner's Manual Page 57

Comments to this Manuals

Related products and manuals for AV receivers Denon 2310CI - AVR AV Receiver