Denon DN-780R User Manual download pdf (Page 9)

ENGLISH

2 MUSIC SEARCH SYSTEM

The music search system detects blank sections

(lasting for at least 4 seconds) between selections in

order to locate the beginning of selections in the

forward or reverse direction.

1. To advance from the current selection to the

beginning of the next selection (CUE) :

Press the Play ( 1 ) button simultaneously with

the Fast Forward ( 7 ) button. Press the Play

( 0 ) button simultaneously with the Rewind

( 6 ) button.

The deck will skip the rest of the current selection

and automatically resume play from the beginning

of the next selection.

2. To repeat playback from the beginning of the

current selection (REVIEW) :

Press the Play ( 1 ) button simultaneously with

the Rewind ( 6 ) button. Press the Play ( 0 )

button simultaneously with the Fast Forward

( 7 ) button.

The deck will rewind the tape to the beginning of

the current selection and automatically resume

play from that point.

This is very convenient for repeating playback of

the current selection.

Notes on Music Search Operation :

The search functions operates by detecting

comparatively long, blank sections approximately 4 to

5 seconds long, in between recorded selections.

Therefore, the system may not operate normally in

the following cases:

• Recordings with discontinuous speech or

conversation.

• Recordings with long periods of pianissimo (softly

played music).

• Blank sections with a high level of noise.

• Blank sections shorter than 4 seconds.

• If noise-emitting appliances, such as electric razors,

drills, refrigerators, etc., are operated nearby.

• REVIEW close to the beginning of the program or

CUE close to the ending.

2 POWER ON PLAYBACK

Playback starts automatically when the power is

turned on.

• Playback is performed according to the reverse

mode set when the power was turned off.

• Playback is performed even if a cassette tape is

only loaded in one deck.

• Playback always starts in the “1” tape travel

direction.

• When tapes are loaded in both Deck A and Deck B,

playback starts from Deck A.

• The power on playback function can be set with

the “PRESET FUNCTION” (page 11).

RECORDING

• The operations described below apply to deck A

and deck B alike.

q Press the POWER switch q to the ON ( ¢ )

position.

w Load the cassette tape !9, !6.

(Check that the erasure prevention tabs of the

cassette housing have not been broken off.)

e Select the Dolby NR type that suits the recording.

r Select the type of tape transport with the REV.

MODE button @0.

t Press the Rec/Rec Mute ( 4 ) button !4 to set the

recording pause mode. The 4 3 indicator will light

up.

y Adjust the recording level with the INPUT LEVEL

control y while watching the Peak Level Meter.

u Recording starts when the Play ( 0 or 1 ) button

!4 for the direction indicated by the flashing tape

travel indicator ( 0 or 1 ) is pressed. If the other

Play ( 0 or 1 ) button !4 is pressed, the direction

of tape travel changes.

The Play ( 0 or 1 ) and the 4 indicator will light

during recording.

i To stop recording, press the Stop ( 2 ) button !4.

o To pause the recording, press the Rec Pause ( 3 )

button !4. Press the Play ( 0 or 1 ) button !4 to

resume recording.

NOTE :

For Deck B, the input source can be selected.

Select the desired line input beforehand using the

INPUT SELECT switch.

DECK A : The sound playing on Deck A can be

recorded. (Refer to “MANUAL DUBBING”

(page 11)).

LINE A : The sound input to the DECK A LINE IN

jacks can be recorded.

LINE B : The sound input to the DECK B LINE IN

jacks can be recorded.

Mode

Indicator

To record on only one side

To continuously record on both

sides

RELAY

CASCADE

Caution :

Be careful not to erase important recordings by

mistake. Inadvertent start of recording will happen

in the following cases:

1. If the Play ( 0 or 1 ) button is pressed while the

4 indicator lights, recording starts.

2. If the Play ( 0 or 1 ) button and Rec/Rec Mute

( 4 ) button are pressed at the same time,

recording starts.

The best way to avoid accidental erasure is to break

off the two erasure prevention tabs on the cassette

housing.

2 PROPER RECORDING LEVEL

A too high recording level can saturate the tape and

cause distortion. On the other hand, if the recording

level is set too low, soft passages will be marked by

residual noise. A proper recording level is the most

important factor for making well balanced recordings.

Guideline for maximum recording level

Type I (Normal)

+3 dB level on peaks

Type II (CrO2)

Type IV (Metal)

+3 dB level on peaks

Note :

The optimum recording level differs depending on

the program source and the type of tape used.

2 REC/REC MUTE AND REC PAUSE BUTTONS

1. To record a 5-second blank section during

recording:

Press the Rec/Rec Mute ( 4 ) button. A 5-second

blank will be recorded and the deck will enter the

recording standby mode.

2. To record a 5-second blank section during the

recording standby mode:

Press the Rec/Rec Mute ( 4 ) button from the

recording standby mode. A 5 second blank will be

recorded and the deck will enter the recording

standby mode again.

3. To cancel recording of blank space:

Press the Rec Pause ( 3 ) button. Blank space

recording will be cancelled and the deck enters

the recording standby mode.

4. To extend the blank section with another 5

seconds or more:

Simply press the Rec/Rec Mute ( 4 ) button and

the blank section will be increased with another 5

seconds.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 17 18

Comments to this Manuals

No comments

Denon DN-780R User Manual Page 9

Comments to this Manuals

Related products and manuals for Cassette Decks Denon DN-780R