Denon AVR-3802 User Manual Page 24

  • Download
  • Add to my manuals
  • Print
  • Page
    / 82
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 23
24
ENGLISH
B
231
BASS TREBLE
[1] Adjusting the sound quality (TONE)
The tone control function will not work in the Direct mode.
After starting playback
1
The tone switches as follows each time the
TONE CONTROL button is pressed.
TONE
CONTROL
(Main unit)
2
With the name of the volume to
be adjusted selected, turn the
SELECT knob to adjust the level.
SELECT
(Main unit)
To increase the bass or treble: Turn the control
clockwise. (The bass or treble sound can be
increased to up to +12 dB in steps of 2 dB.)
To decrease the bass or treble: Turn the
control clockwise. (The bass or treble sound
can be decreased to up to 12 dB in steps of
2 dB.)
B
1
+10
0
TV/
VCR
RDS PTY RT
SURROUND
OUTPUT
TEST
TONE
SPEAKER
5CH / 7CH
STEREO
DOLBY/DTS
SURROUND
DSP
SIMU.
2
[2] Listening over headphones
2
Press the OUTPUT button to play the sound
over the headphones only.
OUTPUT
1
Use this to turn off the audio
output temporarily.
Press the MUTING button.
Cancelling MUTING
mode.
Press the MUTING button again.
MUTING
(Remote control unit)
The output to the speaker and pre-out jacks is
turned off and no sound is produced from the
speakers.
1
Connect the headphones to
the PHONES jack of the front
panel.
1
PHONES
NOTE:
To prevent hearing loss, do not raise the volume level
excessively when using headphones.
Caution: Switching off the power of the unit and
the unit will cancel the settings.
[3] Turning the sound off temporarily (MUTING)
1
2
3
SKIP
SKIP
ENTER
+
-
+
-
TUNER
PHONO
CD
SHIFT
MUTING
TUNING
1
Playback using the external input (EXT. IN) jacks
When the input mode is set to the external input
(EXT. IN), the play mode (DIRECT, STEREO,
DOLBY/DTS SURROUND, 5/7CH STEREO, WIDE
SCREEN or DSP SIMULATION) cannot be set.
NOTES:
In play modes other than the external input
mode, the signals connected to these jacks
cannot be played. In addition, signals cannot be
output from channels not connected to the input
jacks.
The external input mode can be set for any input
source. To watch video while listening to sound,
select the input source to which the video signal
is connected, then set this mode.
1
Set the external input (EXT. IN) mode.
Press the EXT. IN to switch the external input.
Once this is selected, the input signals
connected to the FL (front left), FR (front right),
C (center), SL (surround left), SR (surround
right), SBL (surround back left) and SBR
(surround back right) channels of the EXT. IN
jacks are output directly to the front (left and
right), center, surround (left and right) and
surround back (left and right) speaker systems
as well as the pre-out jacks without passing
through the surround circuitry.
In addition, the signal input to the SW
(subwoofer) jack is output to the PRE OUT
SUBWOOFER jack.
EXT.IN
(Main unit)
EXT.IN
(Remote control unit)
2
Cancelling the external input mode
To cancel the external input (EXT. IN) setting,
press the input mode (AUTO, PCM, DTS) or
ANALOG button to switch to the desired input
mode. (See page 23.)
ANALOG
DTS
AUTO
PCM
(Main unit)
ANALOG
MODE
(Remote control unit)
INPUT
6.1 / 7.1
SURROUND
ANALOG
EXT.INMODE
CALL 2
BACKLIGHT
CALL 1
STEREO
SYSTEM CALL
DIRECT
1
2
B
21
3
If you do not want the bass and treble to be
adjusted, turn on the tone defeat mode.
TONE DEFEAT
(Main unit)
The signals do not pass
through the bass and treble
adjustment circuits, providing
higher quality sound.
Page view 23
1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 81 82

Comments to this Manuals

No comments