Denon AVR-3300 User Manual download pdf (Page 47)

Surround parameters q

CINEMA EQ. (Cinema Equalizer):

The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for overly-bright sounding motion picture

soundtracks. Select this function if the sound from the front speakers is too bright.

This function only works in the Dolby Pro Logic, Dolby Digital and DTS Surround modes.

D.COMP. (Dynamic Range Compression):

Motion picture soundtracks have tremendous dynamic range (the contrast between very soft and very loud sounds). For listening late at night,

or whenever the maximum sound level is lower than usual, the Dynamic Range Compression allows you to hear all of the sounds in the

soundtrack (but with reduced dynamic range). (This only works when playing program sources recorded in Dolby Digital or DTS.) Select one of

the four parameters (“OFF”, “LOW”, “MID” (middle) or “HI” (high)). Set to OFF for normal listening.

LFE (Low Frequency Effect):

This sets the level of the LFE (Low Frequency Effect) sounds included in the source when playing program sources recorded in Dolby Digital

or DTS.

If the sound produced from the subwoofer sounds distorted due to the LFE signals when playing Dolby Digital or DTS sources when the peak

limiter is turned off with the subwoofer peak limit level setting (system setup menu), adjust the level as necessary.

Program source and adjustment range

1. Dolby Digital: –10 dB to 0 dB

2. DTS Surround (–10 dB to 0 dB)

* When DTS encoded movie software is played, it is recommended that the LFE LEVEL be set to 0 dB for correct DTS playback.

* When DTS encoded music software is played, it is recommended that the LFE LEVEL be set to –10 dB for correct DTS playback.

S.Sp (Surround Speaker):

Select the surround speaker to be used. This is not displayed if the surround speaker setting has been set to “None” in the system setup. It

is also not displayed in the direct or stereo modes.

TONE:

This adjusts the tone control. (See “Surround parameters w” on page 52.)

ENGLISH

Display the

surround parameter

menu.

Select the various parameters.

NOTE:

• When “Default” is selected and the cursor button is pressed, “CINEMA EQ.” and “D.COMP.” are automatically turned off, “LFE” is

reset, “S.Sp” is set to “A” and the tone is set to the default value.

• With this model, Dolby Digital encoded signals can only be played in the Dolby Pro Logic, Dolby Digital, DIRECT and STEREO mode. Other

surround mode buttons will not function during the Dolgy Digital signal playback.

• With this mode, DTS signals can only be played in the DTS Surround, DIRECT and STEREO mode. Other surround mode buttons will not

function during the DTS signal playback.

2 Dialogue Normalization

The dialogue normalization function is activated automatically when playing Dolby Digital program sources.

Dialogue normalization is a basic function of Dolby Digital which automatically normalizes the dialog level (standard level) of the signals which are

recorded at different levels for different program sources, such as DVD, DTV and other future formats that will use Dolby Digital.

When this function is activated, the following message appears on the main unit’s display:

DIAL.NORM

OFFSET - 4dB

The number indicates the normalization level when the currently playing program is normalized to

the standard level.

(Remote control unit)

(Main unit)

SELECT

(Remote control unit)(Main unit)

(When displayed with the remote control unit) (When displayed with the buttons on the main unit)

Adjust the parameter settings.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 61 62

Comments to this Manuals

No comments

Denon AVR-3300 User Manual Page 47

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Denon AVR-3300