Denon DRW-695 Operations Instructions download pdf (Page 8)

ENGLISH

PLAYBACK

• The operations described below apply to deck A and deck B alike.

• Switch on your amplifier or receiver.

• Set the Tape Monitor switch on your amplifier or receiver to the TAPE

position.

• The numbers in the illustration below depict the order in which operation

steps are carried out.

q Press the POWER switch

q to the ON ( ¢ ) position.

w Press the EJECT (

5 ) button w to open the cassette compartment cover

!2.

e Load the cassette tape and close the cassette compartment cover

!2.

r When listening to a tape that has been recorded with Dolby noise

reduction, set the DOLBY NR switch

y to match the system used at the

time of recording.

DOLBY NR

B OFF C

t Press the Direction ( 01) button !6 to select the direction of tape

transport.

Transport Direction

Forward

Reverse

Indicator

y Select the type of tape transport with the REVERSE MODE switch u.

REV. MODE

RELAY

Mode

To listen to one side only

To listen to repeat playback of both

sides

To listen to continuous play back of

both sides and both decks.

Switch position

RELAY

u Press the PLAY button !6 to begin playback.

i Press the stop (

2 ) button !6 to stop the playback.

• In the continuous playback mode (REVERSE MODE set to ),

playback of both tape sides will be repeated 5 times and then stop

automatically.

• If different types of Dolby noise reduction are used for record and

playback, playback response will be adversely effected.

• When power is turned off during tape transport, it may not be possible

to remove the cassette by pressing the EJECT (

5 ) button. In this case,

turn on power again before you press the EJECT (

5 ) button.

2 RELAY PLAY (continuous playback of the tapes in deck A and deck B)

• Load a cassette tape into deck A and B, and set the Dolby NR button

correctly.

q REVERSE MODE set to “RELAY”

w Press the PLAY button

!6 of the deck you first wish to listen to.

e To stop relay play, press the stop (

2 ) button !6 of the deck currently

playing the tape.

• Relay play will play decks A and B in succession for 5 cycles, upon which

playback stops. When playback starts from deck B, when switching to

deck A. the first deck A playback cycle will be counted as the second

cycle. The completion of 5 cycles will always be at the opposite side of

the tape in deck B.

2 MUSIC SEARCH SYSTEM

The music search system detects blank sections (lasting for at least 4 seconds)

between selections in order to locate the beginning of selections in the

forward or reverse direction.

1. To advance from the current selection to the beginning of the next selection

(CUE):

Press the PLAY button, keep it pressed in, and press the Fast Forward (

7 )

button when the tape is travelling in the forward ( ) direction.

Press the PLAY button, keep it pressed in, and press the Fast Rewind (

6 )

button when the tape is travelling in the reverse ( ) direction.

The tape transport indicator flashes.

The deck will skip the rest of the current selection and automatically resume

play from the beginning of the next selection.

2. To repeat playback from the beginning of the current selection (REVIEW):

Press the PLAY button, keep it pressed in, and press the Fast Rewind (

6 )

button when the tape is travelling in the forward ( ) direction.

Press the PLAY button, keep it pressed in, and press the Fast Forward (

7 )

button when the tape is travelling in the reverse ( ) direction.

The tape transport indicator flashes.

The deck will rewind the tape to the beginning of the current selection and

automatically resume play from that point.

This is very convenient for repeating playback of the current selection.

Notes on Music Search Operation:

The search functions operates by detecting comparatively long, blank sections

approximately 4 to 5 seconds long, in between recorded selections. Therefore,

the system may not operate normally in the following cases:

• Recordings with discontinuous speech or conversation.

• Recordings with long periods of pianissimo (softly played music).

• Recordings with long silences.

• Blank sections with a high level of noise.

• Blank sections shorter than 4 seconds.

• If noise-emitting appliances, such as electric razors, drills, refrigerators, etc.,

are operated nearby.

• REV close to the beginning of the program or CUE close to the ending.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 68 69

Comments to this Manuals

No comments

Denon DRW-695 Operations Instructions Page 8

Comments to this Manuals

Related products and manuals for Cassette players Denon DRW-695