Denon AVR-1683 Operations Instructions download pdf (Page 16)

1 2 5

o °e_e°°

o 8v ooo

Select the input source to be played

Example: CD

IMain unit} IRemate control unit}

Select the input mode

• Selecting the analog mode

Press the ANALOG button to switch to the

analog input

% %

(Main unit} IRemote control unit}

• Selecting the external input {EXT IN) mode

Press the EXT IN {or the EXT IN button on

the remote control unit) to switch the external

_nput

_.IN

% %

(Main unit} IRemote control unit}

• Selecting the AUTO, PCM and DTS modes

The mode switches as shown below each time

the INPUT MODE button is pressed

AUTO _ PCM _DTS

% %

(Main unit} IRemote control unit}

Input mode selection function

Different input modes can be selected for the different

input sources¸ The selected input modes for the

separate input sources are stored in the memory¸

@)AUTO (All auto mode}

In this mode, the types of signals being input to the

digital and analog input jacks for the selected input

source are detected and the program in the AVR-

1603's surround decoder is selected automatically

upon playback TMs mode can be selected for all

input sources other than TUNER

The presence or absence of digital signals is

detected, the signals input to the digital input iacks

are identified and decoding and playback are

performed automatically in DTS, Dolby Digital or

PCM (2 channel stereo} format If no digital signal

is being input, the analog input jacks are selected

Use this mode to play Dolby Digital signals

PCM (exclusive PCM signal playback mode)

Decoding and playback are only per[ormed when

PCM signals are being input

Note that noise may be generated when using this

mode to play signals other than PCM signals

DTS (exclusive DTS signal playback mode)

Decoding and playback are only per[ormed when

DTS signals are being input

_ANALOG (exclusive analog audio signal playback

mode)

The signals input to the analog input iacks are

decoded and played

EXT IN (external decoder input jack selection mode}

The signals being input to the external decoder

input jacks are played without passing through the

surround circuitry

NOTE:

• Note that noise will be output when CDs or LDs

recorded in DTS format are played in the "PCM"

(exclusive PCM signal playback) or "ANALOG"

(exclusive analog audio signal playback) mode

Select the AUTO or DTS (exclusive DTS signal

playback] mode when playing signals recorded in

DTS from a laser disc player

Notes on playing a source encoded with DTS

• Noise may be generated at the beginning of

playback and while searching during DTS

playback in the AUTO mode. If so, play in the

DTS mode.

• In some rare cases the noise may be generated

when you preform the operation to stop

playback of a DTS-CD or DTS-LD,

Selectthe play mode

Press the SURROUND MODE button, then turn

the SELECT knob

Example: Stereo

su_14coe s_eo

(Main unit} (Remote control unit}

To select the surround mode _

while adiusting the surround

parameters, channel volume or

tone control, press the surround

mode button then operate the (Mainunt)

selector (See page 18)

4 Start playback on the selected component

• For operating instructions, refer to the compenent's

manual

Adjust the volume

The vol_rr e level is

disp r_yed on _e mas%e

voume _evel d splay {Main unit) _Remote control unit}

The volume can be adiusted within the range

ot -70 to 0 to 18 dB, in steps of 1 dB However,

when the channel level is set as described on

page 18, if the volume for any channel is set

at +1 dB or greater, the volume cannot be

adjusted up to 18 dB (In this case the

maximum volume is adiusted to "18 dB --

(Maximum value of channel levell" )

Input mode when playing DTS sources

• Noise will be output if DTS-compatible CDs or LDs

are played in the "ANALOG" or "PCM" mode

When playing DTS-compatible sources, be sure to

connect the source component to the digital input

iacks {OPTICAL/COAXIAL) and set the input mode

to "DTS"

[t] Adjusting the sound quality (tone}

The tone switches as follows each time the TONE

CONTROL button is pressed

BASS _ TREBLE

(Ma_n unit)

Input mode display

• In the AUTO mode

One of these I_gh{s depending

on _he input s_gnal

• In the DIGITAL PCM mode

• In the DIGITAL DTS mode

• In the ANALOG mode

o o

Input signal display

• DOLBY DIGITAL

• DTS

o ,.

• PCM

The _ indicator lights when digital signals

are being input properly If the _ indicator

does not light, check whether the digital input

component setup {page I2) and connections are

correct and whether the component's power is

turned on

NOTE:

• The _ indicator will light when playing

CD-ROMs containing data other than audio signals,

but no sound will be heard

m o • -

3 21

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 194 195

Comments to this Manuals

No comments

Denon AVR-1683 Operations Instructions Page 16

Comments to this Manuals

Related products and manuals for AV receivers Denon AVR-1683