Denon AVR 2805 - AV Receiver Operations Instructions Page 23
- Page / 100
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
23
5
Start the measurements.
Measurement of each channel is performed as follows.
Display
1
Only the front speakers (A) is measured. Even if the front speakers (B)
is set, the setting automatically switches to the front speakers (A) once
measurements are completed.
2
Subwoofer speaker is measured twice.
3
When “ZONE2” is selected, this is not displayed.
After each channel is measured, “Calculating” appears.
The display switches to Auto Setup check screen automatically.
FL
FR CSW
2
3
SBL
SBR
1
SL
SR
About automatic retry
Remeasurement starts automatically to receive proper result of measurement.
Remeasurement is performed to 2 times, and “Retry1” or “Retry2” is displayed on screen during
remeasurement.
About the error message
These error screens will be displayed when performing the measurements of Auto Setup / Room EQ and the automatic measurements can not
be completed because of the speaker arrangement, measurement environment, or other factors. Please check the following matters, reset the
pertinent items, and measure again.
When there is too much noise in the room, the speakers may not be detected properly. Should this happen, perform the measurements when
the noise level is low, or switch off the power of the equipment that is producing the noise for the duration of the measurements.
NOTES:
• Measurement is canceled when MASTER VOLUME
is operated while the Auto Setup is performed.
• Set the volume to halfway and set the crossover
frequency to the maximum or Low pass filter off if
your subwoofer speaker can adjust the output volume
and the crossover frequency.
q This screen will be displayed when the speakers required for
producing suitable reproduction have not been detected.
• The front L and front R speakers were not properly detected.
• Only one channel of the surround speakers was detected.
• Sound was output from the R channel when only one surround
back speaker was connected.
• The surround back was detected, but the surround speaker was
not detected.
Check that the pertinent speakers are properly connected.
(see page 13)
w This screen will be displayed when the speaker polarity is
connected in reverse.
e This screen will be displayed when accurate measurements
cannot be made due to the input level to the microphone being too
high.
Set up the speakers so that their position is farther away from
the listening position.
Lower the volume of the subwoofer speaker.
r This screen will be displayed when the measurement microphone
is not connected, or when all of the speakers have not been
detected.
Connect the measurement microphone to the microphone
connector.
Check the speaker connections.
Check the polarity of the
pertinent speakers.
For some speakers, the
screen below may be
displayed even though
the speakers are properly
connected.
If so, select “Skip0”.
- AVR-2805/985 1
- CAUTION: 2
- ATTENTION 2
- WARNING: 2
- SAFETY INSTRUCTIONS 3
- TABLE OF CONTENTS 4
- BEFORE USING 4
- CAUTIONS ON INSTALLATION 4
- CAUTIONS ON HANDLING 5
- FEATURES 5
- CONNECTIONS 6
- (S-Video jack) 9
- (Color Diffrence Video jack) 9
- (Video jack) (Video jack) 9
- R VIDEO OUTL 12
- S-VIDEO OUT 12
- Speaker system connections 13
- Protector circuit 14
- Note on speaker impedance 14
- PART NAMES AND FUNCTIONS 15
- Remote control unit 17
- SETTING UP THE SYSTEM 18
- Auto Set/RoomEQ 20
- *System Setup 20
- Auto setup/Room EQ 21
- 1-1 Setting the Auto Setup 22
- About automatic retry 23
- About the error message 23
- (Remote control unit) 24
- 1-3 Setting the Room EQ Setup 26
- 1-4 Setting the Direct Mode 27
- 1-6 Check the EQ parameter 28
- Setting the Speaker Setup 29
- Setting the type of speakers 30
- Setting the Delay Time 31
- Setting the Channel Level 32
- FL C FR SR SBR SBL SL SW 33
- Input Setup 36
- COMPONENT 39
- Svideo Video 39
- Auto Tuner Presets 40
- Setting the Advanced Playback 41
- 4-1 Setting the Audio Delay 41
- Setting the Option Setup 42
- Setting the Trigger Out Setup 44
- 5-5 Setting the Muting Level 45
- 5-7 Protecting the setting 46
- After completing system setup 47
- REMOTE CONTROL UNIT 48
- Preset memory 50
- 6,7 : Manual search 52
- 2 : Stop 52
- 3 : Pause 52
- Learning function 53
- System call 54
- Punch Through 55
- Resetting 56
- ON / STANDBY 58
- Playing the input source 59
- MASTER VOLUME 60
- (Main unit) 62
- After starting playback 63
- ZONE 2 / 64
- REC SELECT 64
- MAIN ZONE 7.1-channel systems 65
- MAIN ZONE 5.1-channel systems 66
- SURROUND 68
- Dolby Pro Logic 69
- DTS NEO:6 mode 71
- 4, 5 2, 6 72
- Checking the input signal 73
- DSP SURROUND SIMULATION 76
- DSP surround simulation 77
- Tone control setting 79
- Room EQ OFF 80
- *Surr Parameter 80
- Bass : 0dB 80
- *Tone Control 80
- Surround parameters r 81
- Surround modes and parameters 81
- LISTENING TO THE RADIO 83
- Checking the preset stations 84
- LAST FUNCTION MEMORY 85
- TROUBLESHOOTING 86
- ADDITIONAL INFORMATION 87
- Surround back speakers 88
- Speaker setting examples 89
- Surround 90
- DTS Digital Surround 91
- DTS-ES Extended Surround 92
- DTS 96/24 93
- AL24 Processing 93
- INPUT MODE settings 97
- SPECIFICATIONS 98
- Printed in Japan 511 4172 007 100
- Telephone: (03) 3837-5321 100
Related products and manuals for AV receivers Denon AVR 2805 - AV Receiver
(110 pages)© 2020, manymanuals.com. All rights reserved. | 0.250 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals