Denon AVR-786S Operations Instructions download pdf (Page 13)

Easy Setup and Operation Easy Setup and Operation

• These errer screens may be displayed when performing Auto Setup measurement and the autematic measurements can not be

completed because ef the speaker arrangement, measurement envirenment, or ether facters. Please check the folk)wing matters,

reset the pertinent items, and measure again.

• When there is too much noise in the room, the speakers may net be detected properly. Sheuld this happen, perform the

measurements when the noise level is low, er switch off the power of the equipment that is producing the neise for the duration

of the measurements.

J 1-1. Auto Setup

> Front

Retry_

Cancel4

J 1-1. Auto Setup

> Front

Retry_

Cancel_

Skip4

J 1-1. Auto Setup

_BJ

>Exit_

i 1-1. Auto Setup

i * t I -

J Press Enter or Cursor

J Down to Return to

i Auto Setup Menu

.............................................................................................................................................................................................................._i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_!_i_i_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiil_

11. This screen will be displayed when the speakers

required fer preducing suitable repreduction have

net been detected.

• The front L er front R speaker was net preperly

detected.

• Only one channel of the surreund speakers was

detected.

• Sound was output from the R channel when onlv

one surround back speaker was connected.

• The surround back speaker was detected, but the

surround speaker was net detected.

12] This screen will be displayed when the speaker

pelaritv is cennected in reverse.

_._.:This screen will be displayed when accurate

measurements cannet be made due to the input

level of the micrephone being tee high.

4 This screen will be displaved when the

measurement micrephone is net cennected.

• Check that the pertinent speakers are

preperly connected.

• Check the polaritv of the pertinent

speakers. Fer some speakers, this

screen may be displayed even theugh

the speakers are preperlv cennected. If

so, select "Skip._".

• Set up the speakers se that their pesitien

is farther awav from the listening

pesitien.

• Lower the w)lume ef the subweefer

speaker.

• Connect the measurement micrephone

te the microphone connector.

Press the CURSORA or V button to select an

item. then press the ENTER button.

'- AU[O Se[uo

-Co_3 e_e-

S[ea_et Cent g :heck

Delay Time Chec

Channe Leve Check

Store_

Retry4

Cance q

'_ Tle measurement resul[s 31 eacn ii:er'r can De cnecKea

here

1 Press the ENTERbutton.

• The veril car an screen aeDears.

Example: Seeaker Config. Check

S[eaKer Conf g ]heck

Fro_t SD, _arge

Center SD Sma

Surrounc So Sma

S Back So Sma

S Back S_ 2so

Subwoofer Yes

Press the ENTER button again once you have

checked the results.

I ENGLISH I

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 65 66

Comments to this Manuals

No comments

Denon AVR-786S Operations Instructions Page 13

Comments to this Manuals

Related products and manuals for AV receivers Denon AVR-786S