Denon DN-A7100 - AV Surround Preamplifier User's Guide download pdf (Page 22)

ENGLISH

HDMI JACK

This unit has two HDMI inputs and one HDMI output. It

can send digital video and audio signals from DVDs and

other sources directly to a display. It minimizes signal

degradation caused by analog conversion so that high

quality images can be enjoyed.

Select an input source from the OSD menu system.

(See page 20)

Notes:

• When the HDMI output is connected to a display

monitor that does not support HDCP, signals are not

output. To view images in HDMI, it is necessary to

connect to a display that supports HDCP.

• There may be no image output if connected to a

TV or display that is not compatible with the above

format.

• Refer to the instruction manual of the TV or display

to be connected to the DN-A7100 for detailed

information regarding the HDMI terminal.

* HDCP: High-bandwidth Digital Content Protection

CONNECTING HDMI DEVICES

An HDMI cable (sold separately) is used to connect

the HDMI jack on the DN-A7100 with the HDMI jack

on a DVD player, TV, projector or other component. To

transmit multichannel audio via HDMI, the connected

player must support multichannel audio transmission

through its HDMI jack.

HDMI video streaming is compatible with DVI in

principle. Therefore, it is possible to connect to a TV

or monitor that has a DVI terminal using an HDMI-DVI

conversion cable or plug. When connecting to a DVI

terminal, connect the audio signal separately.

Notes:

• Some HDMI components can be controlled over the

HDMI cable, but this receiver cannot control other

components this way.

• When connected to a monitor (i.e., TV, projector,

etc.) that does not support HDCP, video and audio

are not output.

• DVI cables come with 24-pin and 29-pin plugs. This

receiver supports 24-pin DVI-D cables; 29-pin DVI

cables cannot connect to it.

• Some source devices such as DVD players does not

support HDMI repeater like those of the DN-A7100.

In such case, pictures are not properly projected on

monitors such as TVs and projectors.

• When multiple components are connected to this

receiver, turn power to unused components off to

prevent interference between them.

• Disconnecting or connecting cables with the power

on can damage the equipment. Turn the power off

before disconnecting or connecting cables.

• Some DVD-Audio disks disable downmixing.

These types of disks are not played back correctly

unless the left, center, right and surround left and

right speakers, and subwoofer are connected.

• If a DVD player that does not support HDMI 1.1 is

connected to the DN-A7100, multi channel PCM

playback is not possible even with DVD-Audio

disks.

•

If a DVD player or other device with DVI output is

connected to the DN-A7100, a separate audio cable

(optical-digital, coaxial digital or analog) is needed

for the audio signals. In this case, select the connected

audio input as explained in “1 INPUT SETUP”. (See

page 20)

• Multi channel PCM signals and audio signals of 62

kHz or higher that are input from the HDMI jack are

not output from the DIGITAL OUT jacks.

• Depending on the quiality of the cable used, the

HDMI signal may be affected by noise.

• Audio units that use sampling frequencies of 128

kHz and above are not supported.

DVD player VIDEO PROJECTOR

HDMI OUTPUT

HDMI INPUT

HDMI OUTPUT

Satellite Tuner

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 47 48

Comments to this Manuals

No comments

Denon DN-A7100 - AV Surround Preamplifier User's Guide Page 22

Comments to this Manuals

Related products and manuals for AV receivers Denon DN-A7100 - AV Surround Preamplifier