Denon DN-X800 Operations Instructions download pdf (Page 22)

ENGLISH

Alpha-Track Hot Start mode

Like with buttons A1 and A2, operation is performed

using the (RVS)/FLIP/(CLR), A3, A4 and EXIT/RELOOP

buttons. (Refer to page 16.)

★★ ★★

Hot start mode

Like with buttons A1 and A2, operation is performed

using the (RVS)/FLIP/(CLR), A3, A4 and EXIT/RELOOP

buttons. Operation is same as Hot Start with A1, A2

buttons. See page 16 for details.

Exit and Reloop

u The EXIT/RELOOP button

can be used same as

Seamless Loop function.

Reverse Play

i You can play Sampler sound in

reverse with push RVS (FLIP)

button. In reverse play mode

RVS LED lights up.

• Reverse playback will start with next

playback starting after reverse mode

turned on.

Setting the Sampler volume and pitch

• The sound level (volume) and pitch can be

set individually for Sampler1 and 2.

• See m - step 8 “Adjust sound level and

pitch”.

Clearing the Sampler data

!0 While pressing the (RVS)/FLIP/(CLR)

button, push the SAMP button (SAMP1 or

SAMP2) to clear the Sampler.

• By pushing the (RVS)/FLIP/(CLR) button

for approx. 1 sec, you can clear both

Samplers 1 and 2.

Moving Sampler B point

o When the B button is

pushed during Sampler

playback, the B point moves

to the point at which the

button was pushed, and loop

playback from point A starts.

y, ui, !0 w, oq, r, !0

e, t

Record in Sampler

q When the SAMP button

(SAMP1 (A3) or SAMP2 (A4))

is pushed in the standby or

playing, the sound from A3

or A4 point is recorded to

Sampler memory up to 15

seconds.

• The SAMP1 or SAMP2 button is flashing

while recording. When the recording is

completed, the button turns off and the

corresponding SAMP B LED lights up.

Play Sampler sound

r Playback of the Sampler

sound starts when the

SAMP button is pushed after

recording has stopped.

• Sampler playback continues in looping.

With setting B point, playback loop

between A and B point. Without B point

setting Sampler loops whole recorded

length (about 15 seconds).

NOTE: It is not possible to play Sampler1

and Sampler2 at the same time.

t To stop the Sampler

sound push STOP (a CUE)

button.

Sampler

Stop recording

e To stop recording before

recording finish

automatically with

memory full, push the

STOP (a CUE) button.

• The EXIT/RELOOP LED light to indicates

Sampler Loop mode is set automatically.

SAMP. STOP

DN-S5000 has two Samplers of 15 seconds length. These Samplers are also used in looping playback.

Setting B point

w When the B button is

pushed during Sampler

recording, the Sampler Loop

B point is set and the loop

mode turns on.

• Recording continues for approximately

15 seconds without stopping after set B

point.

• If the B point is not set, recording end

point set as B point automatically. Also

EXIT/RELOOP LED light to indicates

Sampler Loop mode is set automatically.

Select Sampler Loop mode

You can select loop mode for Sampler when

Sampler playback stop.

Loop (default):

Sampler playback continues with

looping.

(EXIT/RELOOP LED stays lit)

Exit: Sampler playback continues over B

point up to recording length.

(EXIT/RELOOP LED flashes)

Single: Sampler playback stops at B point.

(EXIT/RELOOP LED turned off)

y To select loop mode, push

EXIT/RELOOP button after

recording and before playing.

SAMP. STOP

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 48 49

Comments to this Manuals

No comments

Denon DN-X800 Operations Instructions Page 22

Comments to this Manuals

Related products and manuals for DJ controllers Denon DN-X800