Denon DVM-4800 Operations Instructions download pdf (Page 52)

ENGLISH

Use the cursor buttons (

•

) to select the preferred setting and press the

ENTER button.

q When “Speaker Setting” is selected

1. Multi-channel

Speaker presence and size ( )

1. Use the cursor buttons (

•

, 0, 1) to select the item and press the

ENTER button.

2. Use the cursor buttons (

•

) to select the setting and press the

ENTER button.

Icon examples: Surround speaker (L)

Large: When the speaker supports low-frequency (under 100 Hz)

reproduction.

Small: Select when the speaker does not support low-frequency

reproduction.

The size setting for the front speakers is aiutomatically determined by

the setting for the subwoofer.

Changing the delay time ( )

(Dolby Digital, center and surround speakers only)

1. Use the cursor buttons (

•

, 0, 1) to select the delay time box and

press the ENTER button.

2. Use the cursor buttons (

•

) to adjust the delay time and press the

ENTER button.

For optimum listening with 5.1-channel sound, all the speakers, except

for the subwoofer, should be the same distance from the seating position.

If you have to place the center or surround speakers closer to the seating

position, adjust the delay time to make up for the difference.

If distance (from the center speaker) and (from the surround

speakers) are the same as or greater than (from the front speakers),

leave the delay time as “0”, the factory preset.

If either distance or is less than , find the difference in the

relevant table and change to the recommended setting.

Channel balance ( )

1. Use the cursor buttons (

•

, 0, 1) to select “Test” and press the

ENTER button.

A test signal is output from one speaker at time, starting with the

front left speaker and proceeding clockwise.

FRONT (L) CENTER FRONT (R)

SURROUND (L)

SURROUND (R)

2. While listening to the test signal, use the cursor buttons (

•

) to

adjust the volume of the center and surround speakers so they are

the same apparent volume as the front speakers.

(The front speakers cannot be adjusted here.)

3. Press the ENTER button.

The test signal stops.

When you are finished

Use the cursor buttons (

•

, 0, 1) to select “Exit” and press the

ENTER button.

2. When “2-channel” is selected

Settings are not necessary.

No signal is output for the subwoofer. To adjust its volume, play

something, then return to this screen to adjust to suit your taste.

The unit may be unable to output as set here due to limitations imposed

by the unit itself or the disc being played. (The FL display’s “P.PCM”

indicator lights or “D.MIX” indicator goes out in these cases.)

w When “Digital Audio Output” is selected

1. On (Factory default)

Digital signal are output.

2. Off

Digital signals are not output.

This improves sound quality when you are using analog connection.

e When “PCM Down Conversion” is selected

1. No (Factory default)

Digital audio of 48 kHz/16 bit is output during playback of the DVD recorded

in Linear PCM of 48 kHz. No digital audio is output during playback of

the DVD recorded in Linear PCM of 96 kHz. However, audio will be output

using the original audio recording system in case of the DVD which has

not been copyright-protected.

(Remote control unit)

ENTER

(Remote control unit)

ACTION

SELECT

ENTER RETURN

m s

d B

d Bd B

Exit

Test

d B

Center

Front (L)

Front (R)

Surround

(L) a (L)

(R)

(R) a

Subwoofer

Exit

No Large Small

Test

signal

• Center speaker

Difference Setting

Approx. 50 cm (1

1/2

feet) 1.3 ms

Approx. 100 cm (3 feet) 2.6 ms

Approx. 150 cm (5 feet) 3.9 ms

Approx. 200 cm (6 feet) 5.3 ms

• Surround speakers

Difference Setting

Approx. 200 cm (6 feet) 5.3 ms

Approx. 400 cm (12 feet) 10.6 ms

Approx. 600 cm (18 feet) 15.9 ms

Downloaded From Disc-Player.com Denon Manuals

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 58

Comments to this Manuals

No comments

Denon DVM-4800 Operations Instructions Page 52

Comments to this Manuals

Related products and manuals for DVD players Denon DVM-4800