Denon AVR-2310CI User Manual Page 27
- Page / 78
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2
ENGLISH
Getting Started
Connections Playback Remote Control Information Troubleshooting
SpecificationsMulti-Zone
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
1
Check the speaker connections.
(vpage 12 “Connecting the Speakers”)
2
Turn on the power of the TV and subwoofer.
Set the TV’s input to the AVR-2310CI.
3
Turn on the AVR-2310CI’s power.
(vpage 20 “Turning the Power On”)
4
Connect the included calibrated setup microphone to
the SETUP MIC jack on the main unit.
The Audyssey Auto Setup screen appears automatically.
5
Mount the setup microphone on a tripod or stand and
install it at the main listening position.
When installing the setup microphone, adjust its height so that
the section where the sound is received is at the height of the
ears during listening.
Sound
receptor
Setup
microphone
a Connect the included Setup Microphone
When using a subwoofer on which the volume can
be adjusted and the crossover frequency can be set
When using a subwoofer, make the following settings before starting
the Audyssey Auto Setup procedure:
n When using a subwoofer with a direct mode
Set the direct mode to “On” and disable the volume adjustment
and crossover frequency setting.
n When using a subwoofer without a direct mode
Make the following settings:
• Volume : “12 o’clock position”
• Crossover frequency : “Maximum/Highest Frequency”
• Low pass filter : “Off”
• Standby mode : “Off”
NOTE
• Do not hold the microphone in your hand during measurements.
• Avoid placing the microphone close to a seat back or wall as sound
reflections may give inaccurate results.
s Audyssey Auto Setup Preparations
around items indicate the settings made upon purchase.
NOTE
• Do not disconnect the setup microphone until the Audyssey Auto
Setup procedure is completed.
• When using headphones, unplug the headphones before starting
the Audyssey Auto Setup procedure.
Perform the following settings if adjustments, etc., are required for
the speaker environment you’re using.
If you do not need to perform the following settings, or have already
completed them, select “Auto Setup Start” and then press .
Proceed to “
STEP2
”.
STEP1 Preparation
1
Press ui to select
“Amp Assign”, then
press .
2
Press o p to select Amp Assign Mode, then press
.
Normal
: The sound of the surround back channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
ZONE2
: If the ZONE2 power is on, the sound of the
ZONE2 channel is output from the speakers
connected to the SURR. BACK/AMP ASSIGN
terminals.
Front A Bi-Amp
: The sound of the front A bi-amp channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Front B Bi-Amp
: The sound of the front B bi-amp channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Front Height
: The sound of the front height channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Changing the amplifier assignment (Amp Assign)
The signals output from the AVR-2310CI’s SURR. BACK/AMP ASSIGN
speaker terminals can be switched to signals of the surround mode
being used.
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
S T E P 1 P r e p a r a t i o n [ 1 / 6 ]
C o n n e c t t h e s p e a k e r s
a n d p l a c e t h e m a c c o r d -
i n g t o t h e r e c o m m e n d a -
a t i o n s i n t h e m a n u a l .
S e t t h e f o l l o w i n g
i t e m s i f n e s e s s a r y .
A m p A s s i g n
C h a n n e l S e l e c t
A u t o S e t u p S t a r t
E N T E R E n t e r R E T U R N C a n c e l
S e t u s e o f s u r r o u n d b a c k c h . f o r y o u r s y s t e m
n To cancel Audyssey Auto Setup
To cancel, press then use o p to select “�es”.
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
Remote control
operation buttons
:
Displaying the menu
Cancel the menu
Settings
- AVR-2310CI 1
- IMPOTANT SAFETY 2
- INSTRUCTIONS 2
- ENGLISHFRANCAIS 3
- Contents 4
- Cautions on Handling 6
- Cautions on Installation 6
- About the Remote Control Unit 6
- Part Names and Functions 7
- Rear Panel 9
- Remote Control Unit 10
- Specifications 11
- Multi-ZoneSettings 11
- Getting Started 11
- Connections 12
- (Video Conversion Function) 13
- When 5.1ch Connectedn 14
- Installing All the Speakers 14
- When 6.1ch Connectedn 14
- Connecting the Speakers 15
- (R) (L) 16
- Connecting Devices not 17
- Equipped with HDMI terminals 17
- Playback Components 18
- Recording Components 19
- SAT/CABLE Tuner 20
- Other Devices 20
- "69 22
- Once Connections are 23
- Completed 23
- Settings 24
- (Audyssey Auto Setup) 26
- SpecificationsMulti-Zone 27
- See overleaf 28
- Check Audyssey Auto Setup 30
- Setting contents 31
- Speaker Confi g 31
- Multi-Zone 32
- Specifi cations 35
- Decoding mode (Input Mode) 42
- (Antenna Aiming) 44
- Playback 45
- Programs 47
- S R 00 0 S i ri u s I D 48
- * * ** * * * * ** * * 48
- S R 00 1 H i ts 1 48
- C A T : P op s 48
- Selecting the Surround Mode 49
- Surround Mode 50
- (Audio/Video Adjust) 51
- Settings (Audyssey Settings) 53
- Equalizer (Manual EQ) 54
- Checking the Status 56
- (Information) 56
- Convenient functions 57
- Adjust the Volume of the 58
- Different Speakers 58
- (Quick Select Function) 58
- Various Memory Functions 58
- "69 59
- Main Remote Control Unit 60
- (RC-1117) 60
- Blu-ray Disc / DVD Player 61
- Operate Other Devices 62
- (Punch Through Function) 62
- Other Information 63
- DTS Surround 64
- Audyssey 64
- Surround Modes and Parameters 65
- Surround 66
- Troubleshooting 70
- MENU button 71
- DEVICE SELECT : TV 74
- DEVICE SELECT : DVD/HDP 75
- DEVICE SELECT : DVR/VCR 75
- DEVICE SELECT : SAT/CBL 76
- DEVICE SELECT : CD 77
Related products and manuals for Home Theater Systems Denon AVR-2310CI
(76 pages)
(86 pages)© 2020, manymanuals.com. All rights reserved. | 1.576 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals