Denon POA-A1HD Owner's Manual download pdf (Page 31)



Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting

Error Messages

If the auto setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is

displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the auto setup procedure over

again.

Error messages (examples) Cause Measures

No microphone or speaker • Included setup microphone is not connected.

• Not all speakers could be detected.

• The front L speaker was not properly detected.

• Connect the included setup microphone to the

SETUP

MIC jack on the main unit.

• Check the speaker connections.

Ambient noise is too high

or Level is too low

• Too much noise in the room for accurate

measurements to be made.

• Speaker or subwoofer sound is too low for

accurate measurements to be made.

• Either turn off any device generating noise or move it

away.

• Try again when the surroundings are quieter.

• Check the speaker installation and the direction in which

the speakers are facing.

• Adjust the subwoofer’s volume.

None • Displayed speaker could not be detected.

· The front R speaker was not properly detected.

· Only one channel of the surround (A) and

surround (B) speakers was detected.

· Sound was output from the R channel when only

one surround back speaker was connected.

· The surround back or the surround (B) speaker

was detected, but the surround (A) speaker

was not detected.

· When the subwoofer conﬁguration is set at

“2SP L/R”, “2SP MIX”, “3SP L/R/LFE” or “3SP

MIX”, the subwoofer could not be detected.

• Check the connections of the displayed speaker.

Phase • Displayed speaker connected with the polarities

reversed.

• If the XLR pre-out terminal is used, the polarity is

reversed.

• Check the polarities of the displayed speaker.

• Check the polarity setting for the XLR output of the

displayed pre-set channel.

• For some speakers, this error message may be displayed

even if the speaker is properly connected. If you are sure

that the wiring is correct, select “Skip”.

Room EQ

Select room EQ setting method.

[Selectable items]

All

Assign

s Option

Select settings for room EQ, mic, etc.

Direct Mode

Select room EQ use for DIRECT or PURE DIRECT mode.

[Selectable items]

OFF

Mic Select

Select the microphone type if not using supplied mic.

The microphone connected to V.AUX Lch is used.

[Selectable items]

Mic

V.AUX L

NOTE

Be sure to turn the power off before checking the speaker connections.

Select “Retry” to make the measurements again.

Only a professionally certiﬁed installer should ever connect a

professionally-calibrated microphone to the V.AUX L input on the front

panel.

• Sometimes due to the electrical complexities of subwoofers and the interaction with the room, THX recommends setting the level and the

distance of the subwoofer manually.

• Sometimes due to interaction with the room, you may notice irregular results when setting the level and/or distance of the main speakers. If

this happens, THX recommends setting them manually.

• Please note that any THX main speakers should be set to Small (80 Hz). If you set up your speakers using Auto Setup, please make sure

manually that any THX speakers are set to Small with 80 Hz crossover.

d Parameter Check

Check auto setup measurement results.

This is displayed after the auto setup procedure is

completed.

[Selectable items]

Spkr Conﬁg Check

Distance Check

Ch. Level Check

Crossover Check

EQ Check

Restore

The auto setup results can be reset to what was originally calculated

by MultEQ XT when “Restore” is selected.

Setup

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 116 117

Comments to this Manuals

No comments

Denon POA-A1HD Owner's Manual Page 31

Comments to this Manuals

Related products and manuals for Receiver Denon POA-A1HD