Denon POA-A1HD Owner's Manual download pdf (Page 99)



Getting Started Connections Setup Playback Remote Control Multi-Zone Information

Symptom Cause Countermeasure Page

Cannot connect

to network.

• The settings of the SSID

and network key (WEP) are

incorrect.

• The reception is poor and the

signals cannot be received.

• There are multiple networks and

the usable channels overlap.

• Match the network settings with

the AVP-A1HD’s settings.

• Shorten the distance from the

wireless LAN’s access point,

remove any obstacles and

otherwise improve visibility, then

try reconnecting. Also install

away from microwave ovens

and the access points of other

networks.

• Set the access point’s channel

settings away from the channels

used for other networks.

Alternatively, connect using a

network cable.

34, 35

–

Played sound is

interrupted or

sound cannot be

played.

• There are multiple networks and

the usable channels overlap.

• Set the access point’s channel

settings away from the channels

used for other networks.

Alternatively, connect using a

network cable.

–

GWireless LANH

Audio section

• Analog

Input sensitivity / Input impedance: RCA Pre output (unbalanced) : 200 mV / 47 kΩ/kohms

XLR Pre output (balanced) : 400 mV / 100 kΩ/kohms

Frequency response:

10 Hz ~ 100 kHz +1, –3 dB (DIRECT mode)

S/N:

102 dB (IHF–A weighted, DIRECT mode)

Distortion:

0.005 % (20 Hz ~ 20 kHz) (DIRECT mode)

Rated output: RCA Pre output (unbalanced) : 1.2 V

XLR Pre output (balanced) : 2.4 V

• Digital

D/A output:

Rated output — 2 V (at 0 dB playback)

Total harmonic distortion — 0.005 % (1 kHz, at 0 dB)

Dynamic range — 110 dB

Digital input:

Format — Digital audio interface

• Phono equalizer (PHONO input — REC OUT)

Input sensitivity:

2.5 mV

RIAA deviation:

±1 dB (20 Hz to 20 kHz)

S/N:

74 dB (A weighting, with 5 mV input)

Rated output:

150 mV

Distortion factor:

0.03 % (1 kHz, 3 V)

Video section

• Standard video connectors

Input / output level and impedance:

1 Vp-p, 75 Ω/ohms

Frequency response:

5 Hz ~ 10 MHz — +0, –3 dB (when video convert set to “OFF”)

• S-Video connectors

Input / output level and impedance:

Y (brightness) signal — 1 Vp-p, 75 Ω/ohms

C (color) signal — 0.3 (PAL) / 0.286 (NTSC) Vp-p, 75 Ω/ohms

Frequency response:

5 Hz ~ 10 MHz — +0, –3 dB (when video convert set to “OFF”)

• Color component video connector

Input / output level and impedance:

Y (brightness) signal — 1 Vp-p, 75 Ω/ohms

B / CB signal — 0.7 Vp-p, 75 Ω/ohms

R / CR signal — 0.7 Vp-p, 75 Ω/ohms

Frequency response:

5 Hz ~ 100 MHz — +0, –3 dB (when video convert set to “OFF”)

Speciﬁcations

Troubleshooting

1 2 ... 94 95 96 97 98 99 100 101 102 103 104 ... 116 117

Comments to this Manuals

No comments

Denon POA-A1HD Owner's Manual Page 99

Comments to this Manuals

Related products and manuals for Receiver Denon POA-A1HD