Denon DN-A7100 User Manual download pdf (Page 8)

ENGLISH

!8 CLEAR button

Press this button to cancel the station-memory

setting mode or preset scan tuning. (See page 33)

!9 HT-EQ button

Used to turn on or off HT(Home Theater)-EQ mode.

This mode compensates for the audio portion of

a movie sounding “bright”. When this button is

pressed, “EQ” indicator lights up.

@0 MEMORY button

Press this button to enter the tuner preset memory

numbers or station names. (See page 33)

@1 PURE DIRECT button

When this button is pressed once, “SOURCE DIRECT”

appears on the FL display. If pressed again, “PURE

DIRECT” appears. After 2 seconds, the FL display

indication goes out.

In the source/pure direct mode, the tone control

circuitry and bass management are bypassed.

Notes:

• The surround mode is automatically switched to

AUTO when the pure direct/source direct function

is turned on.

• Additionally, speaker configurations are fixed

automatically as follows.

Front SPKR = LARGE

Center SPKR = LARGE

Surround SPKR = LARGE

Surround Back SPKR = LARGE

Sub woofer = YES

@2 AUTO (Auto surround) button

Press this button to select the AUTO mode from the

surround modes. When this mode is selected, the

receiver determines the surround mode corresponding

to a digital input signal automatically.

HEADPHONE jack for stereo

headphones

This jack may be used to listen to the DN-A7100’s

output through a pair of headphones. Be certain

that the headphones have a standard 1 / 4” stereo

phono plug.

!0 MUTE button

Press this button to mute the PreAMP output. Press it

again to return to the previous volume level.

!1 VOLUME control knob

Adjusts the overall sound level. Turning the control

clockwise increases the sound level.

!2 ATT (Attenuate) button

If the selected analog audio input signal is greater

than the capable level of internal processing, the

PEAK indicator will illuminate. If this happens, you

should press the ATT button. “ATT” is displayed

when this function is activated.

The signal-input level is reduced by about half.

Attenuation will not work with the output signal of

“REC OUT” (TAPE, CD-R/MD and VCR output). This

function is memorized for each input function.

!3 INPUT SELECTOR knob

(AUDIO/ VIDEO)

This knob is used to select the input sources.

The video SOURCE, such as TV, DVD, VCR1 and

DSS, selects video and audio simultaneously.

Audio function sources such as CD, TAPE, CDR/MD,

and TUNER may be selected in conjunction with a

Video source.

This feature (Sound Injection) combines a sound

from one source with a picture from another.

Choose the video source ﬁ rst, and then choose a

different audio source to activate this function.

!4 Cursor (1, 2, 3, 4) / ENTER button

Use these buttons when operating the SETUP MAIN

MENU and TUNER function.

!5 EXIT button

This button is used to exit from the SETUP MAIN

MENU.

!6 SIMPLE SETUP button

Press this button to enter the simple setup mode.

You can setup the speaker conditions (speaker sizes,

number of speakers, speaker delay times) quickly by

pressing the cursor buttons.

!7 DISPLAY button

When this button is pressed, the FL display mode

is changed as Surround Mode → Auto-display Off

→ Display Off → Input Function and the display off

indicator(DISP) lights up in condition of DISPLAY

OFF.

FRONT PANEL

o !0 !1

w e t

@2 !8@0 !6

@1 !9 !7 !5@3 !2!3!4

q POWER switch and STANDBY

indicator

Press the button to turn the power ON, and press

again to turn it OFF. If the POWER switch is in the

ON position, the power of this unit can be turned ON/

OFF by pressing the POWER button on the remote

control unit.

When this unit is in the standby mode with the

POWER switch set to the ON position, pressing the

ENTER button also allows to turn the power on.

The STANDBY indicator lights up when this unit

is the standby mode (power OFF) by the remote

control unit.

w KEY LOCK button

Press and hold this button for 3 seconds to set

KEY LOCK mode. When the KEY LOCK mode is

on, the unit can only be operated from the RS232C

or remote control, and operation by the main unit

keys is prohibited. Press and hold this button for 3

seconds to release the KEY LOCK mode.

e KEY LOCK indicator

The indicator is illuminated when in KEY LOCK

mode.

r SURROUND MODE button

You can select the surround mode by pressing this

button.

t HDMI indicator

This indicator is illuminated when HDMI device is

connected to the DN-A7100.

y INFRARED receiving sensor

window

This window receives infrared signals for the remote

control.

u BAND button

Press this button to switch between FM and AM in

the TUNER mode.

i T-MODE button

Press this button to select the auto stereo mode or

mono mode when the FM band is selected.

The “AUTO” indicator lights in the auto stereo mode.

(See page 33)

o MENU button

This button is used to enter the SETUP MAIN

MANU.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 47 48

Comments to this Manuals

No comments

Denon DN-A7100 User Manual Page 8

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Denon DN-A7100