Denon AVR-1912 Owner's Manual Page 81

  • Download
  • Add to my manuals
  • Print
  • Page
    / 134
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 80
78
Audio Adjust
Tone
Adjust the tonal quality of the sound.
Setting items Setting details
Tone Control
Set the tone control function
to “ON” and “OFF”.
ON : Allow tone adjustment (bass, treble).
OFF : Playback without tone adjustment.
“Tone Control” can be set when “Dynamic EQ
®
” (vpage 79) is
set to “OFF”.
NOTE
•“Tone Control” settings are not reflected to ZONE2.
•The tone cannot be adjusted in the “DIRECT” mode.
Bass
Adjust low frequency range
(bass).
–6dB – +6dB
“Bass” can be set when “Tone Control” is set to “ON”.
Treble
Adjust high frequency range
(treble).
–6dB – +6dB
“Treble” can be set when “Tone Control” is set to “ON”.
Audyssey Settings
Default settings are underlined.
Set Audyssey MultEQ
®
XT, Audyssey Dynamic EQ
®
and Audyssey Dynamic Volume
®
. These can be
selected after Audyssey
®
Auto Setup has been performed. For additional information on Audyssey
technology, please see page120.
NOTE
•If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ
®
/Dynamic Volume
®
.
In this case, either perform Audyssey
®
Auto Setup over again or perform “Restore” (vpage19) to
return to the settings after Audyssey
®
Auto Setup was run.
•When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey
Settings” cannot be set.
Setting items Setting details
MultEQ
®
XT
MultEQ
®
XT corrects
both time and frequency
response problems in the
listening area based on
Audyssey
®
Auto Setup
calibration. We recommend
“Audyssey”.
MultEQ
®
XT is the
prerequisite function for
Dynamic EQ
®
and Dynamic
Volume
®
.
Audyssey : Optimize the frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
response.
Manual : Apply frequency response set with “Manual EQ” (vpage79).
OFF : Turn “MultEQ
®
XT” equalizer off.
•“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be selected
after Audyssey
®
Auto Setup has been performed. “Audyssey” is
automatically selected after performing Audyssey
®
Auto Setup. When
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,
illuminates.
•After running Audyssey
®
Auto Setup, if the Speaker Configuration,
Distance, Channel Level, and Crossover Frequency have changed
without increasing the number of speakers measured, only
illuminates.
NOTE
•“MultEQ
®
XT” and “Manual” cannot be selected when “EQ Customize”
is set to “Not Used” (vpage87).
•When using headphones, “MultEQ
®
XT” is automatically set to “OFF”.
“MultEQ
®
XT”, “Dynamic EQ
®
” and “Dynamic Volume
®
” settings are stored for each input source.
Basic version
Advanced version
Information
Advanced version
vSee overleaf
BD
Page view 80
1 2 ... 76 77 78 79 80 81 82 83 84 85 86 ... 133 134

Comments to this Manuals

No comments