Denon AVR-786 User Manual Page 12
- Page / 68
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ENGLISH
9
Easy Setup and Operation Easy Setup and Operation
ENGLISH
Starting Auto Setup
2
Press the CURSOR
DD
or
HH
button to select “Auto
Setup”, then press the ENTER button.
• The “Auto Setup” screen appears.
1
Press the SETUP button.
• The “System Setup” menu appears.
Measurement of each channel is performed as follows:
4
Press the CURSOR
DD
or
HH
button to select
“Start”, then press the CURSOR
FF
button.
• Start the measurements.
FL FR C SW SL SR
SBL SBR
1 2 3
1: Only the front speakers (A) are measured, front speakers
(B) are not available. Even if the front speakers (B) are
set, the setting automatically switches to the front
speakers (A) once measurements are completed.
2: The subwoofer speaker is measured twice.
3: When “ZONE2” and “Bi-Amp” is selected, this is not
displayed.
After each channel is measured, “Calculating” appears.
The display switches to the Auto Setup check screen
automatically.
• Measurement is cancelled if the MASTER VOLUME control knob
is operated while the Auto Setup is performed.
• If the output volume and crossover frequency of your
subwoofer speaker can be changed, then set the volume to
halfway and the crossover filter to maximum or switch off
the low-pass filter.
2 About automatic retry
To confirm the results of the measurements, remeasurement is
automatically performed.
Remeasurement is performed up to 2 times. During this time,
“Retry1” or “Retry2” is displayed on the screen.
NOTE:
• When measurements have been made using the
measurement microphone, speakers with built-in filters,
such as a subwoofer, might be set to a value that differs
from the physical distance because of the internal electrical
delay.
When “S. Back” is selected, the test tone during Auto
Setup will be output from the surround back speaker.
When “ZONE2” is selected, change the setting to
“ZONE2”. The test tone during Auto Setup is set so that it
will not be output to ZONE2 (Another room).
When “Bi-Amp” is selected, change the setting to “Bi-
Amp”. The test tone during Auto Setup is set so that it will
be output from the Bi-Amp speaker.
3
Press the CURSOR
DD
or
HH
button to select
“Power Amp Assign”, then press the CURSOR
FF
or
GG
button to select “S. Back”, “ZONE2” or
“Bi-Amp”.
- AV SURROUND RECEIVER 1
- SAFETY INSTRUCTIONS 2
- ENGLISH FRANCAIS 3
- Getting Started 4
- Accessories 5
- Before using 5
- Cautions on installation 5
- Cautions on handling 5
- Part names and functions 6
- Front panel 6
- Inserting the batteries 6
- Easy Setup and Operation 7
- 2 Connections 9
- 2 Bi-Amp connections 9
- Monitor TV 10
- DVD player 10
- ON/STANDBY 11
- SETUP MIC 11
- SPEAKER A 11
- FL FR C SW SL SR 12
- Connecting Other Sources 14
- On-screen display signals 15
- The video conversion function 15
- Connecting a CD player 16
- Connecting a TV/DBS tuner 16
- Connecting a VCR 17
- Connecting a tape deck 17
- 2 AM loop antenna assembly 18
- ZONE2 out connections 19
- ZONE2 speaker out connections 19
- AC 120 V, 60 Hz 20
- AC outlets (Wall) 20
- Power amplifier 20
- Basic Operation 21
- IN=V SOURCE 22
- 2 Input mode display 23
- 2 Input signal display 23
- 2 Selecting the analog mode 23
- SURROUND PARAMETER 24
- STANDARD DIRECT/STEREO 24
- IIx and Pro Logic II Mode: 25
- SELECTFUNCTION 26
- SURROUND MODE 26
- STANDARD 26
- STATUSINPUT MODE 26
- II x Music: 27
- OFFSET - 4dB 27
- FUNCTION 28
- INPUT MODE 28
- DENON original surround modes 29
- 2 Personal memory plus 29
- TONE DEFEAT 30
- TONE CONTROLSURROUND MODE 30
- FL C FR SR 31
- TREBLEBASS 31
- BAND button to 32
- TUNING (+) or (–) button 32
- Advanced Operation 34
- MODE 1 switch to “VIDEO” 37
- MAIN ZONE 5.1-channel systems 38
- FUNCTION ZONE2/REC SELECT 39
- POWER switch 40
- Advanced Setup – Part 1 41
- Component 44
- S-Video Video 44
- IIx Cinema) 45
- Advanced Setup – Part 2 47
- 1. Auto Setup 51
- 2. Speaker Setup 51
- 3. Input Setup 51
- 4. Advanced Playback 52
- 5. Option Setup 52
- Troubleshooting 53
- Additional Information 54
- [2] DTS Digital Surround 57
- Dolby Pro Logic IIx 57
- 2 DTS Neo:6™ surround 58
- [4] DTS 96/24 58
- [3] DTS-ES Extended Surround™ 58
- 2 DTS-ES™ Discrete 6.1 58
- 2 DTS-ES™ Matrix 6.1 58
- Surround modes and parameters 59
- Specifications 60
- ENGLISHFRANCAIS 61
- TOKYO, JAPAN 68
Related products and manuals for Receivers and Amplifiers Denon AVR-786
(15 pages)
(1 pages)
(37 pages)© 2020, manymanuals.com. All rights reserved. | 2.764 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals