Denon RCD-M33 User Manual download pdf (Page 7)

ENGLISH

PHONES (headphones jack)

• Plug the headphones into this jack.

• No sound is produced from the speakers

when headphones are plugged in.

FUNCTION button

• Use this to select the input (function).

• The input changes in the following order

each time this button is pressed:

Display

• Refer to page 8.

(play/pause) button

• Press this button to start playing a disc.

When the disc tray is closed, playback

begins when this button is pressed.

• When pressed in STANDBY mode, the

power automatically turns on and

playback begins (Auto On function).

Press this button again to stop playback

temporarily.

VOLUME control

• Use this to adjust the overall volume

(Rotary Encorder System).

• The volume increases when the control

is turned clockwise (,) and decreases

when it is turned counterclockwise (.).

• The volume increases and decreases in

35 steps from the minimum (VOLUME

00) to the maximum (VOLUME MAX).

CD TUNER TAPE AUX

8 /– , +/ 9 button

(8, 9 : CD automatic search

reverse/forward button

+ , – : TUNER up/down button)

• Use the 8 and 9 buttons to move

to the beginning of a specific track while

in CD function.

• Use the +/– button to select radio

stations while in TUNER function.

• In TUNER function, press the 2 /BAND

and + buttons at the same time to

change the Preset mode, the 2 /BAND

and – buttons at the same time to

change the Tuning mode.

• Use the +/– button when you adjust

tone control (BASS or TREBLE) and you

select menu function (display, time,

timer, or set up).

(open/close) button

• Press this button to open and close the

disc tray.

• When pressed once, the disc tray opens

out, and when pressed again, the disc

tray closes. If a disc is loaded, the total

number of tracks and total playing time

of the disc are displayed several seconds

after the disc tray is closed.

• When pressed in STANDBY mode, the

CD receiver’s power turns on.

Disc tray

• Load discs here.

Power operation switch (ON/STANDBY)

• This turns the power for the entire

system on and off.

• Press this once to turn the power on,

then press again to set the power to

STANDBY mode.

• The LED color changes as follows,

according to the condition:

During power ON : green

During STANDBY : red

During TIMER STANDBY: orange

✻The muting mode is set when the main

unit’s power button is pressed and when

the standby mode is canceled from the

remote control unit. The power indicator

flashes green when in the muting mode,

then stops flashing and turns green once

the set is in the operational mode.

✻If the indicator is flashing orange

(quickly):

The protective circuit is activated.

If this happens, unplug the power cord

to turn the indicator off, then check the

input and output terminals on the rear

panel. Check in particular for short-

circuiting of the speaker cords. Once all

connections have been corrected, plug

the power cord. (Wait for at least 10

seconds after turning the power off

before turning it back on.)

✻Power is supplied to the RCD-M33 even

when the power is in the standby mode

(The clock is displayed in the clock

display mode.)

Remote sensor

• When operating the remote control unit,

point it at this sensor.

2 /BAND button

( 2 : CD stop button

BAND : TUNER band button)

• In CD function, press this button to stop

playback.

• In TUNER function, each time this

button is pressed, the band and FM

reception mode change as follows:

SDB (Super Dynamic Bass)/TONE

button

• Press this button to select the preferred

sound of TONE CONTROL/SDB. Each

time this button is pressed, the display

changes as follows:

• You can switch the SDB on/off by using

the +/– (up/down) button.

• BASS and TREBLE can be adjusted by

using the +/– (up/down) button.

• When you select S.DIRECT (Source

Direct), SDB/TONE is switched off, and

the sound characteristic becomes flat.

• SDB can be controlled powerful bass

tones when listening at lower volume

levels.

MENU/ SET button

• When pressed in the standby mode, the

standby mode is switched (the clock

display is switched on and off).

• When pressed while the clock is

displayed, the manual time setting mode

is set. (This cannot be set while the

clock is displayed in the standby mode.)

• Switches the display of the timer setting

menu on and off.

• When the function is set to FM and the

CT tuning mode is set, the mode

switches to the auto time setting mode.

• When the function is set to TUNER and

an FM station is being received, if

pressed for more than 1 second, the

display switches to the AUTO PRESET

menu.

SDB BASS S.DIRECTTREBLE

FM AUTO AMFM MONO

PART NAMES AND FUNCTIONS

(See page 3.)

(1) Front Panel

NOTE:

• The SDB should be deactivated when

listening at higher volume levels.

Excessive bass at high volume levels

will result in a distorted sound and

may cause damage to your set and

speaker system.

NOTE:

• Care must be taken when you adjust

the volume as the CD receiver is

equipped with an electronic volume

control. Turn the VOLUME control

slowly referring to the indication on

the display to adjust the volume.

1.RCD-M33-E3-ENG 05.4.13 5:46 PM ページ 7

1 2 3 4 5 6 7 8 9 10 11 12 ... 73 74

Comments to this Manuals

No comments

Denon RCD-M33 User Manual Page 7

Comments to this Manuals

Related products and manuals for CD players Denon RCD-M33