Denon AVR-2310CI User Manual download pdf (Page 53)

0

Getting Started

Connections Remote Control Information Troubleshooting

Speciﬁcations

ENGLISH

Multi-ZoneSettings

Setting items Setting contents

Front Height

Set whether or not to use

the front height channel.

ON : Use the front height channel.

OFF : Do not use the front height channel.

This can also be set by pressing

Subwoofer ATT

Attenuate subwoofer level

when using EXT. IN mode.

ON : The input from the subwoofer channel is attenuated.

OFF : The input from the subwoofer channel is not attenuated. Usually use

in this mode.

Set this to “ON” if the subwoofer channel level seems too high when

playing audio signal.

Subwoofer

Turn subwoofer output on

and off.

ON : The subwoofer is used.

OFF : The subwoofer is not used.

Default

Restores all the surround

parameter settings to their

defaults.

Yes : Reset to the defaults.

No : Do not reset to the defaults.

Setting items Setting contents

Tone Control

Sets the tone control function

ON and OFF.

This can be set when

“Dynamic EQ” (vpage

51) is set to “OFF”.

ON : Allow tone adjustment (treble, bass).

OFF : Playback without tone adjustment.

The tone cannot be adjusted when in the DIRECT mode.

Bass

Adjusts the low frequencies.

This can be set when

“Tone Control” is set to

“ON”.

–6dB ~ +6dB (0dB)

Treble

Adjusts the high

frequencies.

This can be set when

“Tone Control” is set to

“ON”.

–6dB ~ +6dB (0dB)

Setting items Setting contents

MultEQ

Corrects the frequency

response of the different

speakers.

NOTE

• “MultEQ” and “Manual

EQ” settings for which

“Not Used” has been set at

“EQ Customize” (vpage

32) cannot be selected.

• When using headphones,

“MultEQ” is set to “OFF”.

Audyssey : Optimize frequency response of all speakers.

Audyssey Byp.L/R : Optimize frequency response of speakers except

front L and R speakers.

Audyssey Flat : Optimize frequency response of all speakers to ﬂat

response.

Manual : Apply frequency response set with “Manual EQ” (vpage 51).

OFF : The “MultEQ” equalizer cannot be used.

• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is

selected, “ ” lights.

• After running Audyssey Auto Setup, if the Speaker Conﬁguration,

Distance, Channel Level, and Crossover Frequency have changed

without increasing the number of speakers measured, only “ ”

lights.

• This can also be set by pressing .

• When the “Audyssey Auto Setup” (vpage 23) procedure is performed, the “MultEQ”, “Dynamic

EQ” and “Dynamic Volume” functions are enabled.

• Operating conditions for each function

• Dynamic EQ :

When “MultEQ” is set to “ON”

• Dynamic Volume :

When “Dynamic EQ” is set to “ON”

• Setting :

When “Dynamic Volume” is set to “ON”

NOTE

If the speaker settings are changed after the “Audyssey Auto Setup” procedure is performed,

“MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey”

is displayed.

If this happens, either perform the “Audyssey Auto Setup” procedure again, or perform the “Restore”

operation (vpage 27) to restore the settings to as they were after the “Audyssey Auto Setup”

procedure was performed.

MultEQ

Dynamic EQ

Dynamic Volume

Setting

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

Remote control

operation buttons

Displaying the menu

Cancel the menu

Playback

Adjusting the Sound and Picture Quality (Audio/Video Adjust)

Making the MultEQ, Dynamic EQ and Dynamic Volume

Settings (Audyssey Settings)

Default settings are underlined.

Adjusting the Tone (Tone Control)

Default settings are underlined.

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 77 78

Comments to this Manuals

No comments

Denon AVR-2310CI User Manual Page 53

Comments to this Manuals

Related products and manuals for Home Theater Systems Denon AVR-2310CI