Denon AVP-A1HD Owner's Manual Page 84
- Page / 87
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Getting Started Connections Setup Other Operations Multi-Zone Information SpecificationsPlayback Troubleshooting
If a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner’s manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
Troubleshooting
Symptom Cause Countermeasure
Page
AVR-5308CI
AVP-A1HDCI
No sound
is produced
from center
speaker.
• You are playing a monaural
source (TV, AM radio
broadcast, etc.) in the
“STANDARD” (Dolby/DTS
Surround) or “HOME THX
CINEMA” mode.
• The mode is set to
something other than
“STANDARD” (Dolby/DTS
Surround) or “HOME THX
CINEMA” .
43 ~ 45 43 ~ 45
No sound
is produced
from surround
speakers.
• The surround mode is set
to “STEREO”.
• Set to a surround playback
mode.
43 ~ 45
C 49, 50
43 ~ 45
C 51, 52
No sound
is produced
from surround
back speaker.
• Surround back speaker
setting is set to “None”.
• Surround mode not set to
a mode for 6.1- or 7.1-
channel playback.
• The surround back
speaker’s power amplifier
is assigned to a different
channel.
• Set to something other
than “None”.
• Select a surround playback
mode.
• Sound is not output from
the surround back speakers.
Change the settings.
23
43 ~ 45
C 49, 50
28,
59 ~ 74
23
43 ~ 45
C 51, 52
–
GAudioH
When this unit is upgraded, the “Audio” contents are changed.
To check items related to “Audio”, refer to this version of the Owner's
Manual instead of the “Original version”.
Symptom Cause Countermeasure
Page
AVR-5308CI
AVP-A1HDCI
No sound
is produced
from front
height
speaker.
• The settings are not
configured to use front
height speakers.
• The front height speaker
setting is “None”.
• The “Extension Channel”
setting is “Front Wide”.
• In the “Amp Assign”
settings, set to use front
height speakers.
• Set the front height
speakers to something
other than “None”.
• Set the “Extension
Channel” setting to “Front
Height”.
28,
59 ~ 74
23
28
–
23
29
No sound
is produced
from front
wide speaker.
• The settings are not
configured to use front
wide speakers.
• The front wide speaker
setting is “None”.
• The “Extension Channel”
setting is “Front Height”.
• In the “Amp Assign”
settings, set to use front
wide speakers.
• Set the front wide
speakers to something
other than “None”.
• Set the “Extension
Channel” setting to “Front
Wide”.
28,
59 ~ 74
23
28
–
23
29
No sound
is produced
from
subwoofer.
• Subwoofer’s power not
turned on.
• The subwoofer was not
detected by Auto Setup, or
subwoofer is set as “No”
in the speaker settings.
• The subwoofer is not
properly connected.
• The subwoofer volume
setting is too low or “Off”.
• Turn on the subwoofer’s
power.
• Set the subwoofer settings
to “Yes”.
• Check the connections.
• Adjust the subwoofer’s
volume to an appropriate
level.
–
23
7
–
–
23
8
–
No test tones
are produced
when main
remote
control unit’s
TEST button is
pressed.
• Surround mode not set
to “STANDARD” (Dolby/
DTS Surround) or “HOME
THX CINEMA” mode.
• Set to the “STANDARD”
(Dolby/DTS Surround) or
“HOME THX CINEMA”
mode.
43 ~ 45 43 ~ 45
- AVR-5308CI 1
- AVP-A1HDCI 1
- Contents 2
- Getting Started 3
- Deleted Functions 4
- Changed Functions 4
- Changes to the Panel Display 5
- Part Names and Functions 6
- Connections 7
- Speaker Connections 8
- */ */ */ 9
- External Power Amplifier 10
- GUI Menu Operations 11
- · Dynamic Volume 12
- Auto Setup 13
- Before starting Auto Setup 14
- 1 2 3 4 5 6 16
- Error messages 22
- Direct Mode 23
- Manual Setup 24
- Audio Setup 27
- Option Setup 29
- Pre-out Assign 30
- Bright Dim 34
- A8 Firmware Update 35
- S0 Firmware Update 35
- A9 Add New Feature 35
- S1 Add New Feature 35
- Source Select 36
- Settings Related to Playing 37
- Input Sources 37
- Input Mode 40
- Decode Mode 40
- A2 Assign 42
- A3 Assign 42
- Surround Mode 44
- Standard Playback 45
- (Dolby Digital, DTS, etc.) 46
- Parameters 47
- Audyssey Dynamic EQ 50
- Information 53
- Playback 54
- Basic Operation 56
- Listening to Preset Channels 57
- Searching Categories 57
- Presetting Radio Channels 57
- (Preset Memory) 57
- Parental Lock 58
- Channels Directly 58
- Other Operations and 59
- Functions 59
- Setting 1: 61
- Setting 2: 62
- Setting 3: 63
- Setting 4: 64
- Setting 5: 65
- Setting 6: 66
- Setting 7: 67
- Setting 8: 68
- Setting 9: 69
- Setting 10: 70
- Setting 11: 71
- Setting 12: 72
- Setting 13: 73
- Setting 14: 74
- Setting 15: 74
- Setting 16: 75
- Other Information 76
- Surround 77
- Surround Modes and Parameters 78
- Speaker Output 83
- Troubleshooting 84
- Specifications 86
- D&M Holdings Inc 87
- 3520 10058 00AD 87
Related products and manuals for Audio amplifiers Denon AVP-A1HD
Audio amplifiers Denon DNA300M User Manual
(13 pages)
(13 pages)
Audio amplifiers Denon PMA-510AE User Manual
(15 pages)
(15 pages)
Audio amplifiers Denon AVP-A1HD User Manual
(51 pages)
(51 pages)
Audio amplifiers Denon POA-3012CI - Multi-Zone Audio Distribution Power Amplifier Owner's Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.416 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals