36
IV
. Speaker system measurement
• With these measurements, the “Speaker Configuration”, “Delay Time”, “Channel Level”, “Crossover Frequency” and “Room EQ” are analyzed
automatically. The main listening position is measured first, so leave the microphone where it is.
1
Select the “OK Start” and press the Cursor left
button.
Measurements for the first point start.
NOTE:
• With these measurements, test tones are not output from channels to which speakers
have been judged not to be connected in the preliminary measurements. Do not change
the connection of speakers or the subwoofer’s volume after performing the preparation
measurements and before performing these measurements.
(Main unit)
(Remote control unit)
(Main unit)
(Remote control unit)
2
q The screen shown at the right appears once the measurements for the main listening
position are completed.
Next the measurements for the second point will be taken. Place the microphone at the
second listening position. For instructions on the position in which the microphone should
be placed, see page 30. (When making the measurements, be sure to position the
microphone at the approximate ear height of the seated listener(s).)
¥¥¥¥ĹáĹ©łŰůŪ¥ŔŠůŰū
Ŝů¥ŠŜŭ¥ţŠŤŢţů¥Ŝů
őŧŠŜŮŠ¥ūŧŜŞŠ¥ŨŤŞŭŪūţŪũŠ
ĺũş¥ŧŤŮůŠũŤũŢ¥ūŪŮŤůŤŪũ©
¥¥¥¥¥¥¥¥¥ńŜŧŞŰŧŜůŠ
¥¥¥¥¥¥¥¥¥ńŜũŞŠŧ
¥¥¥¥¥¥¥¥¥œŠůŭŴ
¥¥¥¥¥¥¥¥¥ŐŌ¥ŏŠųů
¥
¥¥¥¥ĹáĹ©łŰůŪ¥ŔŠůŰū
¥¥¥¥¥¥¥ŎŠŜŮŰŭŤũŢ
¥
¥¥¥¥¥ĺũş¥őŪŮŤůŤŪũ
¥
¥
¥
¥
¥
¥¥¥¥¥¥¥¥¥ńŜũŞŠŧ
(Main unit)
(Remote control unit)
(Main unit)
(Remote control unit)
w Select the “OK Next” and press the Cursor left
button.
Measurements for the second point start.
3
Perform step 2 repeatedly.
The more measurement points, the better the resulting room correction effect. We recommend a minimum of 6 measurement points –
8 measurement points provides the best room correction effect.
¥¥¥¥ĹáĹ©łŰůŪ¥ŔŠůŰū
Ŝů¥ŠŜŭ¥ţŠŤŢţů¥Ŝů
őŧŠŜŮŠ¥ūŧŜŞŠ¥ŨŤŞŭŪūţŪũŠ
ŨŜŤũ¥ŧŤŮůŠũŤũŢ¥ūŪŮŤůŤŪũ©
¥¥ŔūŠŜŦŠŭ¥ŅŠůŠŞů¥ńţŠŞŦ
¥¥¥¥¥¥¥¥¥ńŜũŞŠŧ
¥¥¥¥¥¥¥¥¥œŠůŭŴ
¥¥¥¥¥¥¥¥¥ŐŌ¥ŔůŜŭů
¥
¥¥¥¥ĹáĹ©łŰůŪ¥ŔŠůŰū
¥¥¥¥¥¥¥ŎŠŜŮŰŭŤũŢ
¥
¥¥¥¥¥ŎŜŤũ¥őŪŮŤůŤŪũ
¥
¥
¥
¥
¥
¥¥¥¥¥¥¥¥¥ńŜũŞŠŧ
Comments to this Manuals