Denon AVR 1603 - AV Receiver Operations Instructions download pdf (Page 17)

Front panel display

• Descriptions of the unit’s operations

are also displayed on the front panel

display. In addition, the display can

be switched to check the unit’s

operating status while playing a

source by pressing the STATUS

button.

ENGLISH

With the name of the volume to

be adjusted selected, turn the

SELECT knob to adjust the level.

• To increase the bass or treble:

Turn the control clockwise.

(The bass or treble sound can

be increased to up to +12 dB in steps of 2 dB.)

•

To decrease the bass or treble: Turn the

control counterclockwise. (The bass or

treble sound

can be decreased to up to –12

dB in steps of 2 dB.)

If you do not want the bass and treble to be

adjusted, turn on the tone defeat mode.

The signals do not pass through the

bass and treble adjustment circuits,

providing higher quality sound.

(Main unit)

[2] Listening over headphones

NOTE:

To prevent hearing loss, do not raise the volume level

excessively when using headphones.

Plug the headphones’ plug into

the jack.

Connect the headphones to

the PHONES jack.

The pre-out output (including

the speaker output) is

automatically turned off

when headphones are

connected.

PHONES

[3] Turning the sound off temporarily (muting)

Use this to turn off the audio output

temporarily.

Press the MUTING button.

Cancelling MUTING mode.

Press the MUTING button again.

Muting will also be cancelled

when MASTER VOL is adjusted

up or down.

(Remote

control unit)

Simulcast playback

Use this switch to monitor a video

source other than the audio source.

Press the VIDEO SELECT button

repeatedly until the desired source

appears on the display.

Cancelling simulcast playback.

• Select “SOURCE” using the VIDEO SELECT

button.

• Switch the program source to the component

connected to the video input jacks.

[4]

Combining the currently playing sound with the desired image

(Remote

control unit)

[5] Checking the currently playing program source, etc.

(Remote

control unit)

Using the dimmer function

• Use this to change the brightness of

the display.

The display brightness changes in

four steps (bright, medium, dim and

off) by pressing the main unit’s

DIMMER button repeatedly.

(Remote

control unit)

BRIGHT MEDIUM

OFF

DIM

Playback using the external input (EXT. IN) jacks

Set the external input (EXT. IN) mode.

Press the EXT. IN button

to switch the external

input.

Once this is selected,

the input signals

connected to the FL (front left), FR (front right),

C (center), SL (surround left) and SR (surround

right) channels of the EXT. IN jacks are output

directly to the front (left and right), center,

surround (left and right) speaker systems

without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer)

jack is output to the PRE OUT SUBWOOFER jack.

Cancelling the external input mode

To cancel the external input (EXT. IN) setting,

press the INPUT MODE (AUTO, PCM, DTS) or

ANALOG button to switch to the desired input

mode. (See page 16.)

(Remote control unit)(Main unit)

• When the input mode is set to the external input

(EXT. IN), the play mode (DIRECT,STEREO,

DOLBY/DTS SURROUND, 5CH STEREO or DSP

SIMULATION) cannot be selected.

2 1

NOTES:

• In play modes other than the external input mode,

the signals connected to EXT. IN jacks cannot

be played. In addition, signals cannot be output

from channels not connected to the input jacks.

• The external input mode can be set for any input

source. To watch video while listening to sound,

select the input source to which the video signal

is connected, then set this mode.

(Remote

control unit)

(Main unit)

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 57 58

Comments to this Manuals

No comments

Denon AVR 1603 - AV Receiver Operations Instructions Page 17

Comments to this Manuals

Related products and manuals for Receiver Denon AVR 1603 - AV Receiver