Denon AVR 4806 - AV Receiver Operations Instructions Page 25
- Page / 154
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
25
Easy Setup and Operation
MeasuresCauseScreen example
About the error message
• These error messages will be displayed when performing the measurements of Auto Setup and the automatic measurements
can not be completed because of the speaker arrangement, measurement environment, or other factors. Please check the
following matters, reset the pertinent items, and measure again. Be sure to turn off the AVR-4806’s power before checking the
speaker connections.
q The speakers required for producing suitable
reproduction have not been detected.
• The front L and front R speakers were not
properly detected.
• Only one channel of the surround (A) and
surround (B) speakers was detected.
• Sound was output from the R channel when
only one surround back speaker was
connected.
• The surround back or the surround (B) speaker
was detected, but the surround (A) speaker
was not detected.
If multiple errors occur, press the CURSOR
FF
or
GG
button to check the contents.
• Check that the pertinent speakers
are properly connected.
w The speaker polarity is connected in reverse.
If multiple errors occur, press the CURSOR
FF
or
GG
button to check the contents.
• Check the polarity of the pertinent
speakers.
• For some speakers, the screen
below may be displayed even though
the speakers are properly connected.
If so, select “Skip
0
”.
e There is too much ambient noise in the room
and the measurements cannot be made
accurately.
r The sound level that is output from the
speakers and/or subwoofer is too low.
• Either turn off the power of the
device that generated the noise
during the measurements or move
the device away.
•Try again at a time when it is quieter.
• Check the placement and orientation
of the loudspeakers.
• Adjust the subwoofer’s output level.
t The measurement microphone is not
connected, or all of speakers have not been
detected.
•Connect the measurement microphone
to the microphone connector.
• Check the speaker connection.
Playing a DVD with Surround Sound
1
Disconnect the microphone from the unit.
2
Select the input source to be played.
3
Select the play mode.
4
5
Adjust the volume.
Start DVD playback.
- AVR-4806 1
- 2 SAFETY PRECAUTIONS 2
- 2 System Setup Menu 3
- FIGURE A 4
- AS PER NATIONAL 4
- ELECTRICAL CODE 4
- 2 Motion sensor 8
- Part names and functions 9
- Front panel 9
- @0 @1 @2 @3 @5@4 10
- #5#6#7 #4 #3 10
- @9#0#1 @8 @7 @6 10
- Getting Started 12
- Easy Setup and Operation 13
- Easy to setup flow 13
- Auto setup flow 13
- Speaker system layout 14
- Speaker connections 15
- 2 Connections 16
- DVD player 17
- Monitor TV 18
- Auto Setup / Room EQ 19
- SETUP MIC jack on the front 20
- Connecting Other Sources 26
- Connecting Other Souces 27
- DBS / BS Tuner 29
- DVD recorder 31
- CD player 32
- Video deck 32
- CD recorder / 33
- MD recorder 33
- Turntable 33
- (MM cartridge) 33
- Connectiong a tape deck 34
- DENON LINK connections 34
- 2 Copyright Protection System 35
- Connecting IEEE1394 devices 37
- 2 AM loop antenna assembly 38
- Connection of AM antennas 38
- Power amplifier 41
- Basic Operation 42
- Playing the input source 43
- THX CINEMA 43
- ROOM EQ button 43
- PHONES jack 44
- MUTING button 44
- ON SCREEN button 45
- INPUT MODE button 45
- SPEAKER button 45
- DIMMER button 45
- STATUS button 45
- 2 Input mode display 46
- 2 Selecting the analog mode 46
- 2 Input signal display 46
- Surround 48
- DIRECT/STEREOPURE DIRECT 49
- SURROUND PARAMETER button 50
- ENTER or SURROUND PARAMETER 50
- STANDARD 52
- STANDARD button to select the 53
- 2 Surround parameters e 54
- IIx, Dolby 54
- 2 Dialogue Normalization 54
- SURROUND 56
- PARAMETER 56
- 2 Surround parameters t 57
- (USER MODE function) 59
- USER MODE button at 59
- 2 Personal Memory Plus 60
- 2 Surround parameters y 62
- 2 Tone defeat mode 63
- 2 Adjusting the tone 63
- FUNCTION 64
- PTY NEWS 67
- A1 AM 87.50MHz 67
- RDS button until “TP SEARCH” 69
- CHANNEL button 69
- Advanced Operation 70
- MODE SELECTOR button for the 72
- 2 System call buttons 77
- 2 Storing system call signals 77
- MODE SELECTOR 78
- 2 All reset function 79
- FUNCTION ZONE3/REC SELECT 82
- ZONE2 SELECT 82
- MODE SELECTOR buttons 83
- Other function 84
- RECOUT SOURCE 85
- DVD 85
- POWER DIRECT/STEREO 86
- PURE DIRECT 86
- 2 Auto Preset Memory 93
- 2 Preset Skip 94
- 2 Preset Name 94
- Advanced Setup – Part 1 100
- IIx cinema) 102
- ENTER button 106
- Front Bi-Amp connections 107
- Advanced Setup – Part 2 113
- Troubleshooting 129
- Additional Information 131
- Surround back speakers 132
- Speaker setting examples 133
- [1] Dolby Surround 135
- [2] DTS Digital Surround 137
- [6] THX Surround EX 141
- 2 Copyright protection system 143
- Introduction 147
- Specifications 150
- 2 Audio section 150
- 2 Video section 150
- 2 General 151
- TOKYO, JAPAN 154
Related products and manuals for Receiver Denon AVR 4806 - AV Receiver
Receiver Denon AVR-488 Owner's Manual
(56 pages)
(56 pages)
Receiver Denon AVR-3803 User Manual
(11 pages)
(11 pages)
Receiver Denon D RCD-M37 Owner's Manual
(39 pages)
(39 pages)
Receiver Denon AVR-1312 Owner's Manual
(16 pages)
(16 pages)
Receiver Denon AVR-2311 User Manual
(94 pages)
(94 pages)
Receiver Denon AVR-2805 User Manual
(2 pages)
(2 pages)
Receiver Denon RCD-M39 User Manual
(42 pages)
(42 pages)
Receiver Denon AVR-1508 Owner's Manual
(62 pages)
(62 pages)
Receiver Denon DRA-F107 Owner's Manual
(21 pages)
(21 pages)
Receiver Denon AVR-2311 User Manual
(98 pages)
(98 pages)
Receiver Denon AVR-1509 Owner's Manual
(56 pages)
(56 pages)
Receiver Denon AVR-1507 User Manual
(61 pages)
(61 pages)
Receiver Denon AVR-X510BT Owner's Manual
(127 pages)
(127 pages)
Receiver Denon DRA-37 Owner's Manual
(60 pages)
(60 pages)
© 2020, manymanuals.com. All rights reserved. | 1.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals