Denon AVR 4806 - AV Receiver Operations Instructions Page 92
- Page / 154
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Advanced Setup – Part 1
92
If you wish to set the input source back to as it was
initially, press the CURSOR H button with the input
source highlighted.
If “Yes” is selected for “Default”, the setting are
automatically reset to the default name.
5
Once all the characters have been input, press
the
ENTER button.
• The “Function Rename” screen reappears.
Use the same procedure to change other input source
names as well.
6
Press the ENTER button to enter the setting.
• The “Audio Input Setup” menu reappears.
• When the input source is selected, the display is as shown
below.
Example: When the name has been changed to “DVD-
5910”
• If you do not wish to assign the device connected by
IEEE1394 cable to an input source, the IEEE1394 input can
be selected by turning the FUNCTION knob. In this case, the
connection information is cleared when the power of the
connected device or the AVR-4806 is turned off, so the
selection procedure must be performed again.
• By default, if no device has been connected using an
IEEE1394 cable in the past, “No Connection” is displayed.
• “Connection Change” is displayed if there is a change in the
IEEE1394 connection status while this screen is displayed.
• If the model name cannot be acquired from the connected
IEEE1394 device, “UNKNOWN” is displayed.
• If an IEEE1394 device other than one for IEEE1394 audio
playback is connected, “Not Play” is displayed and the input
source cannot be assigned.
Setting the IEEE1394 Assign
• Assign the device connected by IEEE1394 cable to an input
source. The power of the device to be assigned must be
turned on ahead of time.
1
Press the CURSOR
DD
or
HH
button to select the
“IEEE1394 Assign” at the “Audio Input
Setup” menu, then press the
ENTER button.
• Display the “IEEE1394 Assign” screen.
2
Press the CURSOR
DD
or
HH
button to select the
device to be assigned to the input source, then
press the
CURSOR
FF
or
GG
button to select the
input source.
3
Press the ENTER button to enter the setting.
• The “Audio Input Setup” menu reappears.
- AVR-4806 1
- 2 SAFETY PRECAUTIONS 2
- 2 System Setup Menu 3
- FIGURE A 4
- AS PER NATIONAL 4
- ELECTRICAL CODE 4
- 2 Motion sensor 8
- Part names and functions 9
- Front panel 9
- @0 @1 @2 @3 @5@4 10
- #5#6#7 #4 #3 10
- @9#0#1 @8 @7 @6 10
- Getting Started 12
- Easy Setup and Operation 13
- Easy to setup flow 13
- Auto setup flow 13
- Speaker system layout 14
- Speaker connections 15
- 2 Connections 16
- DVD player 17
- Monitor TV 18
- Auto Setup / Room EQ 19
- SETUP MIC jack on the front 20
- Connecting Other Sources 26
- Connecting Other Souces 27
- DBS / BS Tuner 29
- DVD recorder 31
- CD player 32
- Video deck 32
- CD recorder / 33
- MD recorder 33
- Turntable 33
- (MM cartridge) 33
- Connectiong a tape deck 34
- DENON LINK connections 34
- 2 Copyright Protection System 35
- Connecting IEEE1394 devices 37
- 2 AM loop antenna assembly 38
- Connection of AM antennas 38
- Power amplifier 41
- Basic Operation 42
- Playing the input source 43
- THX CINEMA 43
- ROOM EQ button 43
- PHONES jack 44
- MUTING button 44
- ON SCREEN button 45
- INPUT MODE button 45
- SPEAKER button 45
- DIMMER button 45
- STATUS button 45
- 2 Input mode display 46
- 2 Selecting the analog mode 46
- 2 Input signal display 46
- Surround 48
- DIRECT/STEREOPURE DIRECT 49
- SURROUND PARAMETER button 50
- ENTER or SURROUND PARAMETER 50
- STANDARD 52
- STANDARD button to select the 53
- 2 Surround parameters e 54
- IIx, Dolby 54
- 2 Dialogue Normalization 54
- SURROUND 56
- PARAMETER 56
- 2 Surround parameters t 57
- (USER MODE function) 59
- USER MODE button at 59
- 2 Personal Memory Plus 60
- 2 Surround parameters y 62
- 2 Tone defeat mode 63
- 2 Adjusting the tone 63
- FUNCTION 64
- PTY NEWS 67
- A1 AM 87.50MHz 67
- RDS button until “TP SEARCH” 69
- CHANNEL button 69
- Advanced Operation 70
- MODE SELECTOR button for the 72
- 2 System call buttons 77
- 2 Storing system call signals 77
- MODE SELECTOR 78
- 2 All reset function 79
- FUNCTION ZONE3/REC SELECT 82
- ZONE2 SELECT 82
- MODE SELECTOR buttons 83
- Other function 84
- RECOUT SOURCE 85
- DVD 85
- POWER DIRECT/STEREO 86
- PURE DIRECT 86
- 2 Auto Preset Memory 93
- 2 Preset Skip 94
- 2 Preset Name 94
- Advanced Setup – Part 1 100
- IIx cinema) 102
- ENTER button 106
- Front Bi-Amp connections 107
- Advanced Setup – Part 2 113
- Troubleshooting 129
- Additional Information 131
- Surround back speakers 132
- Speaker setting examples 133
- [1] Dolby Surround 135
- [2] DTS Digital Surround 137
- [6] THX Surround EX 141
- 2 Copyright protection system 143
- Introduction 147
- Specifications 150
- 2 Audio section 150
- 2 Video section 150
- 2 General 151
- TOKYO, JAPAN 154
Related products and manuals for Receiver Denon AVR 4806 - AV Receiver
Receiver Denon AVR-488 Owner's Manual
(56 pages)
(56 pages)
Receiver Denon AVR-3803 User Manual
(11 pages)
(11 pages)
Receiver Denon D RCD-M37 Owner's Manual
(39 pages)
(39 pages)
Receiver Denon AVR-1312 Owner's Manual
(16 pages)
(16 pages)
Receiver Denon AVR-2311 User Manual
(94 pages)
(94 pages)
Receiver Denon AVR-2805 User Manual
(2 pages)
(2 pages)
Receiver Denon RCD-M39 User Manual
(42 pages)
(42 pages)
Receiver Denon AVR-1508 Owner's Manual
(62 pages)
(62 pages)
Receiver Denon DRA-F107 Owner's Manual
(21 pages)
(21 pages)
Receiver Denon AVR-2311 User Manual
(98 pages)
(98 pages)
Receiver Denon AVR-1509 Owner's Manual
(56 pages)
(56 pages)
Receiver Denon AVR-1507 User Manual
(61 pages)
(61 pages)
Receiver Denon AVR-X510BT Owner's Manual
(127 pages)
(127 pages)
Receiver Denon DRA-37 Owner's Manual
(60 pages)
(60 pages)
© 2020, manymanuals.com. All rights reserved. | 0.338 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals