Denon AVP-A1HD Owner's Manual Page 17
- Page / 87
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Getting Started Connections Other Operations Multi-Zone Information Troubleshooting SpecificationsPlaybackSetup
ENTER
i
i
ENTER
STEP2 Detection & Measurement (main)
• In STEP 2, the subwoofer volume level and main listening point
volume are measured.
• This step automatically checks the speaker configuration and speaker
size, and calculates the channel level, distance, and crossover
frequency. It also corrects distortion in the listening area.
• Install the supplied setup microphone to the main listening point.
1
Measuring the subwoofer volume level
Select “Measure” and then press ENTER.
Measure the subwoofer volume level.
b When “Channel Select” – “Subwoofer” in the GUI menu is set to
“Skip”, the subwoofer volume level is not measured.
b When 2 or 3 subwoofers are used, measure the volume level of
each.
b After measuring the volume level of the subwoofer, if the following
error message is displayed, adjust the subwoofer volume level
using “Adjusting the subwoofer volume level” (vpage 17).
AUTO SETUP
1 2 3 4 5 6
RETURN
Skip
SW Level Matching
The subwoofer's level is too high or low. Please select "SW
Level Matching" and adjust the level of your subwoofer unit.
If you do not want to use the
subwoofer, select "Skip".
Proceed to subwoofer volume adjustment item
Enter Cancel
Caution!
2
Perform measurement of the
main listening position
When the subwoofer volume level measurement
is completely, the connected speakers are detected
automatically.
b The measuring channel changes depending on the setting of
“STEP1 Preparation” (vpage 14).
b It takes a few minutes for speaker measurement to complete.
3
The detected speakers are displayed.
b The illustration below shows an example of when the front
speakers, center speaker, subwoofer, surround speakers and front
height speakers have been detected.
AUTO SETUP
1 2 3 4 5 6
RETURN
Next→Measurement
Retry
STEP2 Speaker Detection Check
Front
Center
Subwoofer
Surround
Surr. Back
Front Height
Yes
Yes
1 spkr
Yes
2 spkrs
Yes
Proceed to STEP 3 after checking speaker connection result
Enter Cancel
b If a connected speaker is not displayed, the speaker may not be
connected correctly. Check the speaker connection.
b To re-measure, press i to select “Retry”, and press ENTER.
4
Use i to select “Next Measurement” and then
press ENTER.
Proceed to “STEP3 Measurement (2nd – 8th)” (vpage 18).
NOTE
If “Caution！” is displayed on the television screen, see “Error
messages” (vpage 21). Check the related items, and implement
the necessary measures. After resolving the error, perform Auto Setup
again.
n When measuring has stopped
Press ENTER.
(Main remote control unit) (Sub remote control unit)
ENTER
i
- AVR-5308CI 1
- AVP-A1HDCI 1
- Contents 2
- Getting Started 3
- Deleted Functions 4
- Changed Functions 4
- Changes to the Panel Display 5
- Part Names and Functions 6
- Connections 7
- Speaker Connections 8
- */ */ */ 9
- External Power Amplifier 10
- GUI Menu Operations 11
- · Dynamic Volume 12
- Auto Setup 13
- Before starting Auto Setup 14
- 1 2 3 4 5 6 16
- Error messages 22
- Direct Mode 23
- Manual Setup 24
- Audio Setup 27
- Option Setup 29
- Pre-out Assign 30
- Bright Dim 34
- A8 Firmware Update 35
- S0 Firmware Update 35
- A9 Add New Feature 35
- S1 Add New Feature 35
- Source Select 36
- Settings Related to Playing 37
- Input Sources 37
- Input Mode 40
- Decode Mode 40
- A2 Assign 42
- A3 Assign 42
- Surround Mode 44
- Standard Playback 45
- (Dolby Digital, DTS, etc.) 46
- Parameters 47
- Audyssey Dynamic EQ 50
- Information 53
- Playback 54
- Basic Operation 56
- Listening to Preset Channels 57
- Searching Categories 57
- Presetting Radio Channels 57
- (Preset Memory) 57
- Parental Lock 58
- Channels Directly 58
- Other Operations and 59
- Functions 59
- Setting 1: 61
- Setting 2: 62
- Setting 3: 63
- Setting 4: 64
- Setting 5: 65
- Setting 6: 66
- Setting 7: 67
- Setting 8: 68
- Setting 9: 69
- Setting 10: 70
- Setting 11: 71
- Setting 12: 72
- Setting 13: 73
- Setting 14: 74
- Setting 15: 74
- Setting 16: 75
- Other Information 76
- Surround 77
- Surround Modes and Parameters 78
- Speaker Output 83
- Troubleshooting 84
- Specifications 86
- D&M Holdings Inc 87
- 3520 10058 00AD 87
Related products and manuals for Audio amplifiers Denon AVP-A1HD
Audio amplifiers Denon DNA300M User Manual
(13 pages)
(13 pages)
Audio amplifiers Denon PMA-510AE User Manual
(15 pages)
(15 pages)
Audio amplifiers Denon AVP-A1HD User Manual
(51 pages)
(51 pages)
Audio amplifiers Denon POA-3012CI - Multi-Zone Audio Distribution Power Amplifier Owner's Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.924 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals