Denon DN-C630 User Manual download pdf (Page 9)

ENGLISH

(2) Rear Panel

ANALOG OUT (BALANCED) connectors

• These are active balanced outputs using XLR type

connectors.

• Connect these connectors to the balanced analog input

connectors on an amplifier or console.

• Pin layout: 1. Common

2. Hot

3. Cold

• Applicable connector: Cannon XLR-3-31 or equivalent

NOTE: Do not short-circuit the hot or cold pin with the

common pin.

ANALOG OUT (UNBALANCED) jacks

• These are unbalanced outputs using RCA type jacks.

• Connect these jacks to the unbalanced analog input jacks

on an amplifier or console.

LEVEL L/R controls

• Use these controls to adjust the level of the audio signals

from the ANALOG OUT (BALANCED) connectors.

REMOTE connector

• This is a parallel remote connector. Use it to control the

DN-C630 with dry contact circuit connections.

• Applicable connector: 25-pin D-sub (male)

• Connector signal layout:

Pin No. Signal name I/O

PLAY tally

PLAY command

PAUSE tally

PAUSE command

CUE tally

CUE command

INDEX 2/INDEX 3 tally

TRACK (+) command

Tally common

TRACK (–) command

Reserved

SEARCH (FWD) command

Reserved

SEARCH (REV) command

Reserved

FADER START command

Tally power supply

Command common

EOM tally

Reserved

TTL (lol = 20 mA)

HCMOS (li = 3 mA)

TTL (lol = 20 mA)

HCMOS (li = 3 mA)

TTL (lol = 20 mA)

HCMOS (li = 3 mA)

TTL (lol = 20 mA)

HCMOS (li = 3 mA)

PHOTO COUPLER

+5 V, 20 mA

(li =10 mA)

TTL (lol = 20 mA)

–

NOTE: The tally output pin has open collector IC specifications

(Imax. 20 mA, Vmax. 5 V), but the maximum supply

current is 80 mA, so use with a total load current of 80

mA or less.

DIGITAL OUT jack

• This is an unbalanced output using an RCA type jack.

• Connect this jack to the unbalanced digital input jack on

an amplifier or console.

• Signal format: Selectable (See Page 22, 9))

(3) Display Window

REPEAT indicator

• This lights when the repeat mode is set.

Time mode indicators

• “ELAPSED” lights when the elapsed time is displayed.

• “REMAIN” lights when the remaining time is displayed.

Play mode indicators

• “SINGLE” lights when in the single track play mode.

• “TOTAL” lights when in the continuous play mode.

Track no. display

• This indicates the track number at the current position.

The track number lights during the track search operation

and when switching to the standby mode.

• If the next track is scheduled, that track number flashes

on the track no. display.

Play pause indicator

Play indicator

Index no. display

• Normally “Tr” is displayed. In the index search mode,

the index number is displayed. If the next index is

scheduled, that index number flashes on the index no.

display. The index number also lights during the index

search operation.

Playing position display

• This indicates the current position within the track’s total

playing time.

Pitch display

• This indicates the set play speed in %.

Program indicator

• This lights when a program is input.

• This flashes when the PROG. IN mode is set.

20 tracks music calendar

• In the single track play mode, only the specified track

lights.

• In the continuous play mode, everything from the

specified track to the last track lights.

• Track numbers are displayed up to track 20. Tracks 21

and on are not displayed.

Playing time display

• This indicates the time of the current position, in minutes

(m), seconds (s) and frames (f).

Character display

• This displays operation messages in the preset and

program modes.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 106 107

Comments to this Manuals

No comments

Denon DN-C630 User Manual Page 9

Comments to this Manuals

Related products and manuals for DJ controllers Denon DN-C630