Denon AVR-4802R User Manual Page 51
- Page / 90
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
51
[2] Listening over headphones
Plug the headphones’ plug into the jack.
Connect the headphones to the PHONES jack.
The pre-out output (including the speaker output) is automatically
turned off when headphones are connected.
NOTE:
To prevent hearing loss, do not raise the volume level excessively
when using headphones.
[3] Turning the sound off temporarily (muting)
1
Use this to turn off the audio output
temporarily.
Press the MUTE button.
Cancelling MUTING mode.
Press the MUTE button again.
(Remote control unit)
[4]
Combining the currently playing sound with the desired image
1
Simulcast playback
Use this switch to monitor a video source other than the audio
source.
Press the VIDEO SELECT button until the desired image
appears.
Cancelling simulcast playback.
• Select “SOURCE” using the video select button.
• Switch the program source to the component
connected to the video input.
1
[5] Checking the currently playing program source, etc.
1
q On screen display
• Each time an operation is performed,
a description of that operation
appears on the display connected to
the unit’s VIDEO MONITOR OUT
jack. Also, the unit’s operating status
can be checked during playback by
pressing the remote control unit’s ON
SCREEN/DISPLAY button.
Such information as the position of the input selector
and the surround parameter settings is output in
sequence.
w Front panel display
• Descriptions of the unit’s operations
are also displayed on the front panel
display. In addition, the display can be
switched to check the unit’s
operating status while playing a
source by pressing the STATUS
button.
e Using the dimmer function
• Use this to change the brightness of
the display.
The display brightness changes in
four steps (bright, medium, dim and
off) by pressing the DIMMER button
repeatedly.
The brightness changes in 3 steps each time the button
is pressed, and finally the display turns off.
STATUS
(Main unit)
1-e 1-w
[6] Switching the surround speakers
1
The surround speakers switch as
shown below each time the SPEAKER
button is pressed.
SURROUND A SURROUND B
SURROUND A+B
This operation is possible when the setting for using both
surround speakers A and B is made at “Speaker
Configuration” in the System Setup Menu.
(Remote control unit)
(Remote control unit)
VIDEO
SELECT
(Main unit)
DIMMER
(Main unit)
1
1
-q
1
IN=V SOURCE
Display
- WARNING: 2
- ATTENTION 2
- SAFETY INSTRUCTIONS 3
- TABLE OF CONTENTS 4
- BEFORE USING 4
- CAUTIONS ON INSTALLATION 4
- CAUTIONS ON HANDLING 5
- FEATURES 5
- R/CR, PB/CB) 5
- CONNECTIONS 6
- Connecting video components 7
- Connecting a monitor TV 8
- Connecting the video decks 8
- VIDEO OUT 9
- COMPONENT 9
- VIDEO IN 9
- AM loop antenna assembly 10
- Connection of AM antennas 10
- INFRARED SENSOR 11
- Protector circuit 12
- Note on speaker impedance 12
- Connections 13
- PART NAMES AND FUNCTIONS 14
- Remote control unit 15
- SETTING UP THE SYSTEM 16
- SB SB SB SB 17
- Before setting up the system 18
- Setting the type of speakers 18
- Crossover frequency 20
- Setting the Subwoofer mode 20
- Setting the delay time 21
- Setting the channel level 23
- FL C FR SR SBR SBL SL SW 24
- Adjusting the audio delay 30
- Auto tuner presets 31
- Protecting the settings 31
- After completing system setup 32
- REMOTE CONTROL UNIT 33
- Inserting the batteries 33
- Preset memory 35
- 6,7 : Manual search 37
- 2 : Stop 37
- 3 : Pause 37
- Learning function 38
- 1, 4, 81, 4, 8 38
- System call 39
- Punch Through 40
- Resetting 41
- OPERATION 46
- Playing the input source 47
- MASTER VOLUME 48
- (Main unit) 49
- (Remote control unit) 49
- After starting playback 50
- IN=V SOURCE 51
- RECOUT SOURCE 52
- M-ZONE SOURCE 53
- ANOTHER ROOM MAIN ROOM 54
- (ON-OFF) 54
- AVR-4802R 55
- CONTROL UNIT 55
- SURROUND 56
- Fader function 57
- INPUT MODE 59
- PARAMETER 59
- Checking the input signal 61
- INPUT SELECTOR 62
- DIAL.NORM 63
- OFFSET + 4dB 63
- Dolby Surround Pro Logic 64
- II Mode: 65
- DTS Neo:6 mode 66
- Adjusting the Audio Delay 67
- DENON ORIGINAL SURROUND MODES 68
- DSP surround simulation 69
- Tone control setting 70
- Surround modes and parameters 71
- LISTENING TO THE RADIO 73
- Checking the preset stations 74
- LAST FUNCTION MEMORY 75
- TROUBLESHOOTING 76
- ADDITIONAL INFORMATION 77
- Surround back speakers 78
- Speaker setting examples 79
- Surround 81
- 2 DTS-ES 83
- 2 DTS Neo:6 83
- SPECIFICATIONS 89
- Telephone: (03) 3837-5321 90
Related products and manuals for Receiver Denon AVR-4802R
Receiver Denon AVR-788 User Manual
(74 pages)
(74 pages)
Receiver Denon S-302 User Manual
(58 pages)
(58 pages)
Receiver Denon POA-A1HDCI User Manual
(124 pages)
(124 pages)
Receiver Denon AVC-A1XV User Manual
(70 pages)
(70 pages)
Receiver Denon AVR-1507 User Manual
(64 pages)
(64 pages)
Receiver Denon AVR-688 User Manual
(68 pages)
(68 pages)
Receiver Denon AVR-3313CI User Manual
(10 pages)
(10 pages)
Receiver Denon AVR-4308 User Manual
(116 pages)
(116 pages)
Receiver Denon AVR-5308CI User Manual
(132 pages)
(132 pages)
Receiver Denon AVR-985SP User Manual
(2 pages)
(2 pages)
Receiver Denon AVR-3310 User Manual
(2 pages)
(2 pages)
Receiver Denon AVR-E200 User Manual
(12 pages)
(12 pages)
Receiver Denon AVR-3313CI Specifications
(24 pages)
(24 pages)
Receiver Denon DRA-F109 Owner's Manual
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 0.962 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals