Denon AVR-3805 Operations Instructions Page 15
- Page / 64
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
15
ENGLISH
About the error message
These error screens will be displayed when performing the measurements of Auto Setup / Room EQ and the
automatic measurements can not be completed because of the speaker arrangement, measurement
environment, or other factors. Please check the following matters, reset the pertinent items, and measure again.
When there is too much noise in the room, the speakers may not be detected properly. Should this happen,
perform the measurements when the noise level is low, or switch off the power of the equipment that is
producing the noise for the duration of the measurements.
1
Select the items.
The measurement results of each item can be
checked here.
CH SEL
ENTER
CH SEL
ENTER
Sp Config.Check
*Auto Setup
(Main unit)(Remote control
unit)
Check of the measurement results
q This screen will be displayed when the speakers
required for producing suitable reproduction have
not been detected.
• The front L and front R speakers were not
properly detected.
• Only one channel of the surround (A) and
surround (B) speakers was detected.
• Sound was output from the R channel when
only one surround back speaker was connected.
• The surround back or the surround (B) speaker
was detected, but the surround (A) speaker was
not detected.
Check that the pertinent speakers are properly
connected.
(see page 9)
w This screen will be displayed when the speaker
polarity is connected in reverse.
Check the polarity of the pertinent speakers.
For some speakers, the screen below may be
displayed even though the speakers are
properly connected. If so, select “Skip
0
”.
e This screen will be displayed when accurate
measurements cannot be made due to the input
level to the microphone being too high.
Set up the speakers so that their position is
farther away from the listening position.
Lower the volume of the subwoofer speaker.
r This screen will be displayed when the
measurement microphone is not connected, or
when all of the speakers have not been detected.
Connect the measurement microphone to the
microphone connector.
Check the speaker connections.
2
Press the ENTER button
and display the verification
screen.
CH SEL
ENTER
CH SEL
ENTER
(Main unit)(Remote control
unit)
[Speaker Config. Check] [Delay Time Check] [Channel Level Check]
3
If the check ends, press the ENTER button again.
CH SEL
ENTER
CH SEL
ENTER
(Main unit)(Remote control
unit)
4
Select from the following three items based
on the measurement results.
• Set with the checked measurement
value.
• Perform the measurement again.
• Cancel the checked measurement
value.
CH SEL
ENTER
CH SEL
ENTER
Store
*Auto Setup
(Main unit)(Remote control
unit)
5
When the “Store” is selected, all parameters
are stored up.
When the “Retry” is selected, it measures
again.
CH SEL
ENTER
CH SEL
ENTER
(Main unit)(Remote control
unit)
NOTE:
• When measurements have been
made using the measurement
microphone, speakers with a built-in
filter such as subwoofers might be set
with a value that differs from the
physical distance because of the
internal electrical delay.
- AVR-3805 1
- RISK OF ELECTRIC SHOCK 2
- DO NOT OPEN 2
- BEFORE USING 3
- CAUTIONS ON INSTALLATION 3
- CAUTIONS ON HANDLING 3
- FEATURES 4
- CONNECTIONS 5
- (Component - Y, P 6
- /CR, PB/CB) Video jacks 6
- The Video Conversion Function 6
- DENON LINK connections 8
- Speaker system connections 9
- Protector circuit 9
- Note on speaker impedance 9
- Front Panel 10
- PART NAMES AND FUNCTIONS 10
- Remote control unit 11
- SETTING UP THE SYSTEM 11
- Before setting up the system 13
- Auto setup/Room EQ 13
- 1-1 Setting the Auto Setup 14
- About automatic retry 14
- About the error message 15
- 1-3 Setting the Room EQ Setup 16
- OFF Normal 16
- Manual Flat 16
- 1-4 Setting the Direct Mode 17
- 1-6 Check the EQ parameter 17
- Setting the Speaker Setup 18
- 2-2 Setting the Delay Time 19
- 2-3 Setting the Channel Level 20
- Setting the Input Setup 22
- 3-5 Auto Tuner Presets 24
- Setting the Advanced Playback 25
- 4-1 Setting the Audio Delay 25
- Setting the Option Setup 26
- 5-5 Setting the Muting Level 28
- 5-7 Protecting the setting 29
- After completing system setup 29
- REMOTE CONTROL UNIT 30
- Preset memory 31
- Learning function 33
- System call 33
- Punch Through 34
- Setting the brightness 34
- Resetting 35
- OPERATION 36
- MASTER VOLUME 37
- BASS TREBLE 38
- After starting playback 38
- SURROUND A SURROUND B 39
- SURROUND A+B 39
- MULTI ZONE 40
- SURROUND 41
- (RECOUT) 41
- Fader function 42
- DTS NEO:6 mode 43
- DOLBY PLIIx DTS NEO:6 43
- 5, 612 34 44
- (Remote control unit) 45
- Adjusting the Audio Delay 46
- DSP SURROUND SIMULATION 47
- DSP surround simulation 47
- Tone control setting 48
- LISTENING TO THE RADIO 50
- Auto tuning 50
- Manual tuning 50
- Checking the preset stations 51
- Recalling preset stations 51
- RDS (Radio Data System) 52
- RDS search 52
- PTY search 53
- TP search 53
- LAST FUNCTION MEMORY 54
- RT (Radio Text) 54
- TROUBLESHOOTING 54
- ADDITIONAL INFORMATION 55
- Speaker setting examples 56
- Surround 57
- DTS Digital Surround 58
- DTS-ES Extended Surround 58
- Surround modes and parameters 61
- II / II x ONLY 62
- SPECIFICATIONS 63
- Telephone: (03) 3837-5321 64
Related products and manuals for AV receivers Denon AVR-3805
(65 pages)
AV receivers Denon AVR-390 Owner's Manual
(39 pages)
(39 pages)
AV receivers Denon AVR-S500BT Owner's Manual
(140 pages)
(140 pages)
(74 pages)© 2020, manymanuals.com. All rights reserved. | 0.893 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals