Denon MULTEQXT AVR-4306 Operations Instructions download pdf (Page 8)

Getting Started Getting Started

Cautions on handling

• Switching the input source when input terminals are not connected.

A clicking noise may be produced if the input source is switched when nothing is connected to

the input terminals. If this happens, either turn down the MASTER VOLUME control knob or

connect components to the input terminals.

• Muting of PRE OUT terminals, PHONES jack and SPEAKER terminals.

The PRE OUT terminals, PHONES jack and SPEAKER terminals include a muting circuit. Because

of this, the output signals are greatly attenuated for several seconds after the power switch is

turned on or the input source, surround mode or any other set-up is changed. If the volume is

turned up during this time, the output will be very high after the muting circuit stops functioning.

Always wait until the muting circuit turns off before adjusting the volume.

• Whenever the power switch is in the STANDBY state, the unit is still connected to AC line

voltage.

Please be sure to turn off the power switch or unplug the cord when you leave home for,

say, a vacation.

Preparing the remote control unit

The included remote control unit (RC-1024) can be used to operate not only the AVR-4306 but other

remote control compatible DENON components as well. In addition, the memory contains the

control signals for other remote control units, so it can be used to operate non-DENON remote

control compatible products.

Cautions on installation

Noise or disturbance of the picture may be

generated if this unit or any other electronic

equipment using microprocessors is used near

a tuner or TV.

If this happens, take the following steps:

• Install this unit as far away as possible

from the tuner or TV.

• Run the antenna wires from the tuner or

TV away from this unit’s power supply cord

and input/output connection cables.

• Noise or disturbance tends to occur

particularly when using indoor antennas or

300 Ω/ohms feeder wires. We

recommend using outdoor antennas

and 75 Ω/ohm coaxial cables.

Wall

Note

Note:

For heat dispersal, do not install this unit in a confined space such as a bookcase or similar

enclosure.

Operating range of the remote control unit

30°

Approx. 23 feet / 7 m

• Point the remote control unit at the remote sensor on the main unit as shown in the diagram.

• The remote control unit can be used from a straight distance of approximately 23 feet/7 meters

from the main unit, but this distance will be shorter if there are obstacles in the way or if the

remote control unit is not pointed directly at the remote sensor.

• The remote control unit can be operated at a horizontal angle of up to 30 degrees with respect

to the remote sensor.

NOTE:

• It may be difficult to operate the remote control

unit if the remote sensor is exposed to direct

sunlight or strong artificial light.

• Do not press buttons on the main unit and

remote control unit simultaneously. Doing so

may result in malfunction.

• Neon signs or other devices emitting pulse-

type noise nearby may result in malfunction,

so keep the set as far away from such devices

as possible.

Inserting the batteries

q Remove the remote control unit’s rear

cover.

w Set two LR6/AA batteries in the battery

compartment in the indicated direction.

e Put the rear cover back on.

Notes on batteries:

• Replace the batteries with new ones if the set

does not operate even when the remote

control unit is operated nearby the unit. (The

included batteries are only for verifying

operation.)

• When inserting the batteries, be sure to do so

in the proper direction, following the “<” and

“>” marks in the battery compartment.

•To prevent damage or leakage of battery fluid:

• Do not use a new battery together with an

old one.

•Do not use two different types of batteries.

• Do not short-circuit, disassemble, heat or

dispose of batteries in flames.

• If the battery fluid should leak, carefully wipe

the fluid off the inside of the battery

compartment and insert new batteries.

• When replacing the batteries, have the new

batteries ready and insert them as quickly as

possible.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 145 146

Comments to this Manuals

No comments

Denon MULTEQXT AVR-4306 Operations Instructions Page 8

Comments to this Manuals

Related products and manuals for AV receivers Denon MULTEQXT AVR-4306